IBM C1B 1.12 Brick On Sled Carrier 128-pin HPC, C1C 1.12 3.5-inch Small FF 38-pin Unitized, C2B 2.25 Brick On Sled carrier 128-pin HPC, C4B 4.51 Brick On Sled carrier 128-pin HPC, C4C 4.51 3.5-inch Small FF 38-pin Unitized, SSA 7.2.3.1 Nonoperating Vibration

USER RESPONSIBLE FOR VERIFYING VERSION AND COMPLETENESS

OEM FUNCTIONAL SPECIFICATION ULTRASTAR XP (DFHC) SSA MODELS 1.12/2.25 GB -1.0" HIGH

Table 16. Random Vibration Levels

Class 5hz 17 hz 45 hz 48 hz 62 hz 65 hz 150 h z 200 hz 500 hz RMS

V4 2.0E-5 1.1E-3 1.1E-3 8.0E-3 8.0E-3 1.0E-3 1.0E-3 8.0E-5 8.0E-5 0.56

V4S 2.0E-5 1.1E-3 1.1E-3 8.0E-3 8.0E-3 1.0E-3 1.0E-3 4.0E-5 4.0E-5 0.55

units g2/hz g

Swept Sine Vibration

The drive will operate without hard errors when subjected to the swept sine vibration of 1.0 G peak from 5

to 300 hz in the x- an d y direction. For input in the z-direction, an input of1.0 G peak amplitude can be

applied from 5 hz to 250 hz, the amplitude at 300hz is 0.5 G peak. Linear interpolation is used to deter-

mine the acceleration levels between 250 hz and 300 hz.

The test will consist of a sweep from 5 to 300hz and back to 5 hz. The sweep rate will b e one hz per

second.

Note: 1.0 G acceleration at 5 hz requires 0.78 inch double amplitude displacement.

(The connector on the right edge does not represent SSA connector)

Figure 24. Ultrastar XP SSA Drive Small Form Factor Assembly —CxC Models

7.2.3.1 Nonoperating Vibration

No damage will occur as long as vibration at the un-packaged drive i n all three directions defined above does

not exceed t he levels defined in the table below. The test will consist of a sweep from 5 hz to 200 hz and

back to 5 hz at a sweep rate of eight decades per hour.

Source filename=OPLIMITS IBM Corporation Page 81 of 87

Contents

Main Page Preface Page Contents Page Page Page 1.0 Description 1.1 Features 1.1.1 General Features 1.1.2 Performance Summary 1.1.3 Interface Controller Features 1.2 Models 2.0 Specifications 2.1 General Page 2.1.1 Capacity Equations 2.1.1.1 For Each Notch 2.1.1.2 For Entire Drive 2.2 Power Requirements by Model 2.2.1 C1x Models 2.2.1.1 Power Calculation Examples Page Page Page Page 2.2.2 C2x Models 2.2.2.1 Power Calculation Examples Page Page Page Page 2.2.3 C4x Models 2.2.3.1 Power Calculation Examples Page Page Page Page 2.2.4 CxB Models 2.2.4.1 Power supply methods 2.2.4.2 DC/DC Converter 2.2.5 Power Supply Ripple 2.2.6 Grounding Requirements of the Disk Enclosure 2.2.7 Hot plug/unplug support Page 2.2.8 Bring-up Sequence (and Stop) Times Page Page 3.0 Performance 3.1 Environment Definition 3.2 Workload Definition 3.2.1 Sequential 3.2.2 Random 3.3 Command Execution Time 3.3.1 Basic Component Descriptions Page 3.3.2 Comments 3.3.2.1 Theoretical Data Sector Transfer Rate 3.4 Approximating Performance for Different Environments 3.4.1 For Different Transfer Sizes 3.4.2 When Read Caching is Enabled 3.4.3 When Write Caching is Enabled 3.4.4 When Adaptive Caching is Enabled 3.4.5 When Read-ahead is Enabled 3.4.6 When No Seek is Required 3.4.7 For Queued Commands 3.4.7.1 Reordered Commands 3.4.7.2 Back-To-Back Commands 3.4.8 Out of Order Transfers 3.5 Skew 3.5.1 Cylinder to Cylinder Skew 3.5.2 Track to Track Skew 3.6 Idle Time Functions 3.6.1 Servo Run Out Measurements 3.6.2 Servo Bias Measurements 3.6.3 Predictive Failure Analysis 3.6.4 Channel Calibration 3.6.5 Save Logs and Pointers 3.7 Command Timeout Limits Page 4.0 Mechanical 4.1 Small Form Factor Models (CxC) 4.1.1 Weight and Dimensions 4.1.2 Clearances 4.1.3 Mounting Page Page Page Page Page 4.2 Carrier Models (CxB) 4.2.1 Weight and Dimensions 4.2.2 Clearances 4.2.3 Mounting Page Page 4.2.4 Auto-docking Assembly Side Rails Page Page 5.0 Electrical Interface 5.1 SSA Unitized Connector 5.2 Carrier Connector Page 5.3 SSA Link Cable 5.4 SSA Link Electrical Characteristics 5.5 Option Pins and Indicators 5.5.1 - Manufacturing Test Mode (Option Port Pin 1) 5.5.2 - Auto Start Pin (Option Port Pin 2) 5.5.4 - Write Protect (Option Port Pin 4) 5.5.5 - Ground long (Option Port Pin 5) 5.5.6 - Device Activity Pin/Indicator (Option Port Pin 6) 5.5.7 + 5V (Option Port Pin 7) 5.5.8 - Device Fault Pin/Indicator (Option Port Pin 8) 5.6 Front Jumper Connector 5.7 Spindle Synchronization 5.7.1 Synchronization overview 5.7.2 Synchronization Mode 5.7.3 Synchronization time 5.7.4 Synchronization with Offset 5.7.5.2 Over Sync Hard-wire Page Page 6.0 Reliability 6.1 Error Detection 6.2 Data Reliability 6.3 Seek Error Rate 6.4 Power On Hours Examples: Page 6.7 *Mean Time Between Failure (*MTBF) 6.7.1 Sample Failure Rate Projections 6.8 SPQL (Shipped product quality level) 6.9 Install Defect Free Page 7.0 Operating Limits 7.1 Environmental 7.1.1 Temperature Measurement Points Page 7.2 Vibration and Shock 7.2.1 Drive Mounting Guidelines 7.2.2 Output Vibration Limits 7.2.3 Operating Vibration 7.2.3.1 Nonoperating Vibration 7.2.4 Operating Shock 7.2.5 Nonoperating Shock 7.3 Contaminants 7.4 Acoustic Levels Page 8.0 Standards 8.1 Safety 8.2 Electromagnetic Compatibility (EMC) Page Bibliography