IBM RS/6000 SP Switch power (MAP 0610)

3. Is the yellow switch supervisor LED On or flashing?

vIf yes, return to “Step 0600-010” on page1-12 and continue service with the next highest priority.

vIf no, go to “Step 0620-021” on page1-27.

Switch power (MAP 0610)

Purpose of this MAP

This MAP provides diagnostic steps for resolving problems related to SP Switch2 power.

Note: Refer to “Service position procedures” on page3-10 for placing the switch into the service position

or removing it from the service position.

Step 0610-001

A power problem with the switch was detected.

1. On the switch, check the status condition of the green switch supervisor LED.

2. Status condition for the green switch supervisor LED is as follows:

Green (power) LED

Off No 48 V dc power available at switch.

Flashing

Power available at switch, but switch logic is Off.

On Power available at switch, and logic is On.

3. Is the green switch supervisor LED Off?

vIf yes, go to “Step 0610-004” on page1-14.

vIf no:

– The green switch supervisor LED is On or flashing.

– Go to “Step 0610-002”.

Step 0610-002

1. Is the green switch supervisor LED flashing?

vIf the green LED is flashing, go to “Step 0610-003”.

vIf the green LED is lit but not flashing:

a. This indicates that you do not have a power supply problem.

b. Verify that you have the proper switch, then restart “Switch description and problem

determination (MAP 0590)” on page 1-1.

c. If this is the proper switch, call the next level of support.

Step 0610-003

The green switch supervisor LED is flashing.

1. Attempt to power up the switch using Perspectives from the control workstation.

vNote the status of the green switch supervisor LED.

2. Does green LED light and stay lit?

vIf yes, go to Switch function (MAP 0620) and refer to “Step 0620-021” on page1-27 and return the

switch to the active configuration.

vIf the green LED continues flashing,goto″Frame supervisor not responding (MAP 0110)″in

RS/6000 SP: System Service Guide

.

Switch environment (MAP 0600)

Chapter1. Maintenance Analysis Procedures (MAPs) 1-13

Contents

Main Page Page Page Contents iv Figures Page Tables Page Safety and environmental notices Safety notices (in English) SPSFD003 SPSFD002 SPSFD001 x Caution notices xii SPSFC016 SPSFC017 SPSFC018 Laser safety information Laser Compliance Environmental notices Product recycling and disposal Page About this book RS/6000 SP: SP Switch Service Guide RS/6000 SP: POWER3 SMP High Node Service Guide RS/6000 SP: SMP Thin and Wide Node Service Guide RS/6000 SP: 604 and 604e SMP High Node Service Guide Users responsibilities : Diagnosis Guide xvi Parallel System Support Programs for AIX How to use this book Chapter 1. Maintenance Analysis Procedures (MAPs) Switch MAPs Switch description and problem determination (MAP 0590) 1-2 Page Step 0590-001 Step 0590-002 1-4 Step 0590-003 Page Table1-1. Switch Problem Diagnostics (continued) Switch supervisor communications (MAP 0595) 1-6 Table1-2. SP Switch2 supervisor LED indications Step 0595-001 Step 0595-002 Step 0595-003 Step 0595-004 Step 0595-005 Step 0595-006 Step 0595-007 1-8 Step 0595-008 Step 0595-009 Switch environment (MAP 0600) Step 0600-001 Step 0600-002 Step 0600-003 Step 0600-004 1-10 Table1-4. Fan Failure Diagnostics Step 0600-005 Step 0600-006 Step 0600-007 Step 0600-008 1-12 Step 0600-009 Step 0600-010 Switch power (MAP 0610) Step 0610-001 Step 0610-002 Step 0610-003 Step 0610-004 Step 0610-005 1-14 Step 0610-006 Step 0610-007 Step 0610-009 Step 0610-010 Step 0610-011 Step 0610-012 Step 0610-013 Step 0610-017 Step 0610-018 1-16 Step 0610-019 Step 0610-020 Switch function (MAP 0620) Step 0620-001 Diagnosis Guide PrimaryNodename Diagnosis Guide Step 0620-002 Step 0620-003 1-18 b. Return to Step 0620-001 on page1-17. Table1-6. SP Switch2 error conditions Table1-6. SP Switch2 error conditions (continued) 1-20 <adapter_name> Parallel System Support Programs for AIX: Diagnosis Guide Table1-6. SP Switch2 error conditions (continued) Step 0620-004 1-22 Step 0620-005 Step 0620-006 Step 0620-007 Step 0620-008 Step 0620-009 Step 0620-011 1-24 Table1-8. Service Request Numbers (SRNs) for SP Switch2 adapters (continued) Step 0620-012 Table1-9. Switch Problem Priority Listing Step 0620-013 Step 0620-014 Step 0620-015 1-26 Step 0620-016 Step 0620-017 Step 0620-019 Step 0620-020 Step 0620-021 not 1-28 Chapter 2. Locations Naming standard for RS/6000 SP components Format structure Example of format structure Frame (WWW) Location diagrams of the RS/6000 SP components Front and rear views of RS/6000 SP frame Figure 2-2 shows a front view of the RS/6000 SP multi-switch frame. 2-4 Figure 2-3on page 2-5 shows a rear view of the RS/6000 SP frame locations. SP Switch Frame Locations - Front View ABC Figure 2-2. Front view of multi-switch frame locations Frame locations Frame (FRA) 2-6 Page Page Page Table2-1. External cable routing Cable routing in a multi-switch frame (F/C 2032) 2-10 Switch data cables SP Switch2 data cables Table2-2 describes the attachment locations and routing for the internal SP Switch2 data cables. Table2-2. SP Switch2 data cable chart 2-12 Chapter 3. Service procedures Personal ESD requirements Tools and files overview Table3-1. Service procedure tools 3-2 <adapter_name> Table3-2. Setup output files Using the css.snap script css.snap file structure Files collected by css.snap 3-4 Table3-4. SP Switch2 log files (continued) css.snap file package names yymmddhhmmss 3-6 Hostname Disk space handling Self-test Conditions Switch supervisor status verification using Perspectives Opening a switch pane Checking switch status Base code verification Updating the SP Switch2 supervisor code 3-8 Removing and restoring switch resources Removing an SP Switch2 from the active configuration Administration Guide RS/6000 SP: System Service Guide Restoring an SP Switch2 to the active configuration Using Perspectives to fence and unfence nodes attached to the switch Fencing nodes 3-10 not Unfencing nodes Replacing an SP Switch2 from service position Resetting the clock and bootlist after servicing a node Running diagnostics on a switch port 3-12 Chapter 4. FRU removals and replacements Handling static-sensitive devices SP Switch2 service procedures SPSFC002 4-2 Removing a fan assembly Replacing a fan assembly Removing a power supply Replacing a power supply Removing the LED bracket assembly Replacing the LED bracket assembly 4-4 Removing the switch supervisor card Replacing the switch supervisor card Removing an interposer card 4-6 Replacing an interposer card Removing the switch planar Replacing the switch planar Removing the 48 V dc circuit breaker assembly 4-8 Replacing the 48 V dc circuit breaker assembly Removing the LED power extension cable Replacing the LED power extension cable 4-10 Chapter 5. Parts catalog Page Table5-1. SP Switch2 assembly (view 1) Page Table5-2. SP Switch2 assembly (view 2) Page Table5-3. Switch cables SP Switch2 Frame (F/C 2032) FRONT 5-8 Table5-4. SP Switch2 Frame (F/C 2032) Page Table5-5. F/C 2032 frame extender SP Switch2 Frame Model 556 and F/C 2034 5-12 Table5-6. SP Switch2 Frame Model 556 and F/C 2034 Page Table5-7. Model 556 and F/C 2034 frame extender Page Notices Trademarks Electronic emissions notices Federal Communications Commission (FCC) statement European Union (EU) statement A-2 United Kingdom telecommunications safety requirements Notice to customers For installations in Japan: Electromagnetic interference (EMI) statement - Taiwan Radio protection for Germany Page Index Numerics A B C D H I X-2 L M S T U V Page Readers comments Wed like to hear from you Readers Comments Wed Like to Hear from You IBMR ___________________________________________________________________________________________________ GA22-7444-03 BUSINESS REPLY MAIL