IBM mode, source, Problem, unusual, or both, not work, blinking, No picture, the screen, 7. Appendix, becomes dark, Will turn off, Does not turn on

	7. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 53.)
Problem	Check These Items
Does not turn on	• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
	control is on. See pages 20 and 21.
	• Ensure that the lamp cover is installed correctly. See page 51.
	• Check to see if the projector has overheated or the lamp usage exceeds 2100* hours (up to 3100* hours : Eco
	mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is par-
	ticularly warm, move the projector to a cooler location.
	* VT575 and VT47: 3100 hours (up to 4100 hours in Eco mode).
	• The lamp may fail to light. Wait a full minute and then turn on the power again.
	• The lamp has reached the end of its usable life. Replace the lamp.
Will turn off	• Ensure that the Power Management is off. See page 45.
No picture	• Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Computer,
	Video or S-Video). See page 23. If there is still no picture, press the button again.
	• Ensure your cables are connected properly.
	• Use menus to adjust the brightness and contrast. See page 38.
	• Remove the lens cap.
	• Reset the settings or adjustments to factory preset levels using the “Default” in the Menu. See page 47.
	• Enter your registered keyword if the Security function is enabled. See page 42.
	• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
	on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
	PC is turned on after connecting with the projector.
	* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
	saver or power management software.
	• See also the next page.
Picture suddenly	• When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
becomes dark	* When there are no signals (blue or black screen) → To return to the Normal mode, select another available
	source.
	* When the image is muted using the PIC-MUTE button on the remote control → Press the PIC-MUTE button
	again to return to the Normal mode.
	* When the room where you' re presenting is particularly warm → Move the projector to a cooler location.
Color tone or hue is	• Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 37.
unusual	• Adjust "Hue" in "Picture". See page 38.
Image isn’t square to	• Reposition the projector to improve its angle to the screen. See page 24.
the screen	• Use the Keystone correction function to correct the trapezoid distortion. See page 26.
Picture is blurred	• Adjust the focus. See page 25.
	• Reposition the projector to improve its angle to the screen. See page 24.
	• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See
	pages 11 for VT676/VT670/VT575/VT470 and 12 for VT47.
	• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
	Should this happen, let the projector stand until there is no condensation on the lens.
Image is scrolling	• Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Video, S-
vertically, horizontally	Video or Computer). See page 23.
or both	• Adjust the computer image manually with the Horizontal/Vertical in the “Advanced → Page 2”. See page 45.
Remote control does	• Install new batteries.See page 10.
	• Make sure there are no obstacles between you and the projector.
not work	• Stand within 22 feet (7 m) of the projector. See page 10.
Indicator is lit or	• See the POWER/STATUS/LAMP Indicator on page 53.
blinking
Cross color in RGB	• Press the AUTO ADJ. button on the projector cabinet or the remote control. See page 28.
mode	• When “Off” is selected in Auto Adjust, adjust the computer image manually with Clock/Phase in “Advanced →
	Page 2” in the menu. See pages 45 and 46.

For more information contact your dealer.

54