Manuals / Ice-O-Matic / Kitchen Appliance / Ice Maker

Ice-O-Matic GEM1256A/W, GEM0956A/W, GEM0655 Air GEM 0650/0956/1256 A/W, For the Installer, Page

Models: GEM0650A/W GEM0655 Air GEM0956A/W GEM1256A/W

1 43

Download 43 pages 62.33 Kb

Page 12

Image 12

GEM 0650/0956/1256 A/W

For the Installer

Allow 6 “Clearance for Air Circulation

A proper installation locates the	Two Units on One Bin
ice machine indoors, but in a
ice machine indoors, but in a
place where the heat and noise it
produces are not objectionable.

Air cooled machines discharge hot air out the back and must have a minimum of 6 inches of clearance behind the ice machine.

Space for maintenance access is also important. If two units are placed side by side on a bin, side access becomes even more important.

Page 6

Page 12

Image 12

Ice-O-Matic GEM1256A/W, GEM0956A/W, GEM0655 Air, GEM0650A/W GEM 0650/0956/1256 A/W, For the Installer, Page

Contents

SERVICE AND INSTALLATION MANUAL GEM0650A/W,GEM0956A/W and GEM1256A/WGEM0655 Air Page GEM0650/0956/1256 A/W ForwardKeep this manual for future reference PageTable Of Contents Table of ContentsFreight Claim Procedure Inspect PromptlyVisible Loss or Damage Concealed Loss or DamageWarranty ICE-O-MaticLimitation of Warranty Filing a ClaimFor the Installer Installation GuidelinesElectrical Specifications AdjustmentsFor The Installer GEM0650/0655/0956A/WGEM1256A/W Ice Machine Specifications Bin ApplicationLocation Storage BinIce machine Water LimitationsGEM 0650/0956/1256 A/W For the Plumber Water InletWATER COOLED MODELS AIR COOLED MODELSFor the Electrician Electrical ConnectionsWater Cooled Models Air Cooled ModelsGEM0650/0956/1256A/W Final Check ListStart Up Pre-StartInspectionStart Up Component Description Air Cooled Model ShownGEM0650/0956/1256 A/W Component Description Ice Sweep Bearing Breaker/Divider Auger Evaporator Motor Water SealTo Reset Electrical SequenceElectrical Sequence Shut DownOperation Water Water SystemHigh Pressure Cut Out- Automatic Reset Low Pressure Cut Out- Automatic ResetOperation: Performance Typical Low Side PressureSanitizing and Cleaning ICE MAKING SYSTEM: In place cleaningscheduled at a minimum of twice a year KEEP OUT OF THE REACH OF CHILDRENBearing Maintenance Bearing MaintenanceNote Left Hand Threads Sensor Maintenance Bin Control SensorWater Sensor Maintenance Air Cooled Clean the air cooled condenserGEM0956 GEM0650Auger Maintenance 1. Disconnect electrical power to the ice machineAuger 2. Turn off the water supply to the ice machineService Diagnosis SymptomPossible Cause Probable CorrectionService Diagnosis Control System Diagnostics 4.High pressure cut out checkR&R- Water Reservoir, Bin Control Water ReservoirBin Controls Ice Level Sensors To Remove the Breaker Bearing Assembly R&R-Bearingand BreakerR&R-Auger To Remove the AugerR&R-WaterSeal To Remove the Water SealRemoval of the Water Seal To Replace the Water SealR&R-Evaporator To Replace the EvaporatorTo Reassemble the Evaporator and Auger To Remove and Repair the Gear Motor Assembly R&R-GearMotorTo Check the Gear Motor To Inspect the Gear MotorR&R-FanBlade and Motor Refrigeration Service Instructions for Liquid Charging R404AGEM0650 Wiring Diagram Wiring Diagram GEM0650 A/WGEM0956 Wiring Diagram Wiring Diagram GEM0956 A/WGEM1256 Wiring Diagram Wiring Diagram GEM1256 A/WGEM0655 Wiring Diagram Wiring Diagram GEM0655 AirService History What to Do Before Calling for Service