Operation Water, Water System, Page | Ice-O-Matic GEM0956A/W

GEM0650/0956/1256 A/W

Operation: Water

Water enters the machine through the 3/8 inch male flare at the rear of the cabinet, goes to the water reservoir which it enters through the float valve. The water then goes out the bottom of the reservoir tank to the bottom of the evaporator. Reservoir overflow or evaporator condensation is routed to the drain.

Water cooled models have a separate water circuit for the cooling water. The water enters at the rear, goes to the water regulating valve, then to the water cooled condenser and down the drain.

Water System

Water Inlet

Reservoir

Water Level

Ice Chute

Drain	Evaporator Drain	Evaporator Water Inlet
Drain

Page 15

Page 21

Image 21

Ice-O-Matic GEM0956A/W, GEM1256A/W, GEM0655 Air, GEM0650A/W Operation Water, Water System, GEM0650/0956/1256 A/W, Page

Contents

SERVICE AND INSTALLATION MANUAL GEM0650A/W,GEM0956A/W and GEM1256A/WGEM0655 Air Page Forward GEM0650/0956/1256 A/WKeep this manual for future reference Page Table of Contents Table Of Contents Inspect Promptly Freight Claim ProcedureVisible Loss or Damage Concealed Loss or Damage ICE-O-Matic WarrantyLimitation of Warranty Filing a Claim Installation Guidelines For the InstallerElectrical Specifications Adjustments GEM0650/0655/0956A/W For The Installer GEM1256A/W Bin Application Ice Machine Specifications Storage Bin LocationIce machine Water Limitations GEM 0650/0956/1256 A/W Water Inlet For the PlumberWATER COOLED MODELS AIR COOLED MODELS Electrical Connections For the ElectricianWater Cooled Models Air Cooled Models Final Check List GEM0650/0956/1256A/W Start Up Pre-StartInspectionStart Up Air Cooled Model Shown Component Description GEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider Auger Electrical Sequence To ResetElectrical Sequence Shut Down Water System Operation Water Low Pressure Cut Out- Automatic Reset High Pressure Cut Out- Automatic ResetOperation: Performance Typical Low Side Pressure ICE MAKING SYSTEM: In place cleaning Sanitizing and Cleaningscheduled at a minimum of twice a year KEEP OUT OF THE REACH OF CHILDREN Bearing Maintenance Bearing MaintenanceNote Left Hand Threads Sensor Maintenance Bin Control SensorWater Sensor Clean the air cooled condenser Maintenance Air CooledGEM0956 GEM0650 1. Disconnect electrical power to the ice machine Auger MaintenanceAuger 2. Turn off the water supply to the ice machine Symptom Service DiagnosisPossible Cause Probable Correction Symptom 4.High pressure cut out check Control System Diagnostics R&R- Water Reservoir, Bin Control Water ReservoirBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing Assembly To Remove the Auger R&R-Auger To Remove the Water Seal R&R-WaterSealRemoval of the Water Seal To Replace the Water Seal R&R-Evaporator To Replace the EvaporatorTo Reassemble the Evaporator and Auger R&R-GearMotor To Remove and Repair the Gear Motor AssemblyTo Check the Gear Motor To Inspect the Gear Motor R&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration Service Wiring Diagram GEM0650 A/W GEM0650 Wiring Diagram Wiring Diagram GEM0956 A/W GEM0956 Wiring Diagram Wiring Diagram GEM1256 A/W GEM1256 Wiring Diagram Wiring Diagram GEM0655 Air GEM0655 Wiring Diagram What to Do Before Calling for Service Service History

Ice-O-Matic GEM0956A/W, GEM1256A/W Operation Water, Water System, GEM0650/0956/1256 A/W, Page

Models: GEM0650A/W GEM0655 Air GEM0956A/W GEM1256A/W

Operation: Water

Water System