Manuals / Ice-O-Matic / Kitchen Appliance / Ice Maker

Ice-O-Matic GEM0956A/W, GEM1256A/W, GEM0650A/W R&R-FanBlade and Motor, GEM0650/0956/1256 A/W, Page

Models: GEM0650A/W GEM0655 Air GEM0956A/W GEM1256A/W

1 43

Download 43 pages 62.33 Kb

Page 37

Image 37

GEM0650/0956/1256 A/W

R&R-Fan Blade and Motor

To Remove the Condenser Fan Motor Assembly: (GEM0956 Shown)

1. Disconnect electrical power to the ice machine

2. Remove top panel and the service panels.

3. Unplug the fan motor wire leadsfrom the fan motors.

4. Remove the two (2)head bolt from the top end of the fan motor assembly. (Fig 1)

5. Lift up the fan motors and bracket assembly about 1⁄2 inch and pull out the fan assembly out the right service access hole. (Fig 2)

6. Repair as needed.

7. To Reassemble: Place the fan motor assembly lower flange holes over the two Allen head cap screws in the base, and install the hex head boltsat the top of the assembly. Plug the fan motors back in and replace the panels.

Fig.1

Fig. 2

Page 31

Page 37

Image 37

Ice-O-Matic GEM0956A/W, GEM1256A/W, GEM0655 Air, GEM0650A/W R&R-FanBlade and Motor, GEM0650/0956/1256 A/W, Page

Contents

GEM0650A/W,GEM0956A/W and GEM1256A/W SERVICE AND INSTALLATION MANUALGEM0655 Air Page Forward GEM0650/0956/1256 A/WKeep this manual for future reference Page Table of Contents Table Of Contents Inspect Promptly Freight Claim ProcedureVisible Loss or Damage Concealed Loss or Damage ICE-O-Matic WarrantyLimitation of Warranty Filing a Claim Installation Guidelines For the InstallerElectrical Specifications Adjustments GEM0650/0655/0956A/W For The Installer GEM1256A/W Bin Application Ice Machine Specifications Storage Bin LocationIce machine Water Limitations GEM 0650/0956/1256 A/W Water Inlet For the PlumberWATER COOLED MODELS AIR COOLED MODELS Electrical Connections For the ElectricianWater Cooled Models Air Cooled Models Final Check List GEM0650/0956/1256A/W Pre-StartInspection Start UpStart Up Air Cooled Model Shown Component Description GEM0650/0956/1256 A/W Component Description Evaporator Motor Water Seal Ice Sweep Bearing Breaker/Divider Auger Electrical Sequence To ResetElectrical Sequence Shut Down Water System Operation Water Low Pressure Cut Out- Automatic Reset High Pressure Cut Out- Automatic ResetOperation: Performance Typical Low Side Pressure ICE MAKING SYSTEM: In place cleaning Sanitizing and Cleaningscheduled at a minimum of twice a year KEEP OUT OF THE REACH OF CHILDREN Bearing Maintenance Bearing MaintenanceNote Left Hand Threads Bin Control Sensor Sensor MaintenanceWater Sensor Clean the air cooled condenser Maintenance Air CooledGEM0956 GEM0650 1. Disconnect electrical power to the ice machine Auger MaintenanceAuger 2. Turn off the water supply to the ice machine Symptom Service DiagnosisPossible Cause Probable Correction Symptom 4.High pressure cut out check Control System Diagnostics Water Reservoir R&R- Water Reservoir, Bin ControlBin Controls Ice Level Sensors R&R-Bearingand Breaker To Remove the Breaker Bearing Assembly To Remove the Auger R&R-Auger To Remove the Water Seal R&R-WaterSealRemoval of the Water Seal To Replace the Water Seal To Replace the Evaporator R&R-EvaporatorTo Reassemble the Evaporator and Auger R&R-GearMotor To Remove and Repair the Gear Motor AssemblyTo Check the Gear Motor To Inspect the Gear Motor R&R-FanBlade and Motor Instructions for Liquid Charging R404A Refrigeration Service Wiring Diagram GEM0650 A/W GEM0650 Wiring Diagram Wiring Diagram GEM0956 A/W GEM0956 Wiring Diagram Wiring Diagram GEM1256 A/W GEM1256 Wiring Diagram Wiring Diagram GEM0655 Air GEM0655 Wiring Diagram What to Do Before Calling for Service Service History