Icom IC-F5063, IC-F5062, IC-F5061 manual Transmit Adjustment, Power

6-3 TRANSMIT ADJUSTMENT

Select an adjustment item using [↑] / [↓] keys, then set to the specified value using [←] / [→] keys on the connected PC’s keyboard.

ADJUSTMENT		ADJUSTMENT CONDITION		UNIT	OPERATION			VALUE
OUTPUT	1	• Channel	: CH 5	Rear	Connect an RF power meter to		50 W [USA]
POWER		• Transmitting		panel	the antenna connector.	25 W [EUR], [EXP]
[Power (Hi)]
[Power (L2)]	2	• Channel	: CH 6				25 W [USA]
		• Transmitting				10 W [EUR], [EXP]
[Power (L1)]	3	• Channel	: CH 3				5.0 W [USA]
		• Transmitting				2.5 W [EUR], [EXP]
MODULATION	1	Set the preset value of [MOD N] to “100” on the adjustment software.
BALANCE
	2	• Channel	: CH 7	Rear	Connect the modulation ana-	Set to square wave
[BAL (Narrow)]
		• No audio signals applied to the JIG cable.		panel	lyzer with an oscilloscope to the			form
		• Set a modulation analyzer as;			antenna connector through an
		HPF	: OFF		attenuator.
		LPF	: 20 kHz
		De-emphasis	: OFF
		Detector	: (P–P)/2
		• Push [P0] while transmitting.
FM	1	• Connect an audio generator to the JIG		Rear	Connect the modulation ana-	±2.05 to ±2.15 kHz
DEVIATION		cable and set as;		panel	lyzer to the antenna connector
		Frequency	: 1.0 kHz		through an attenuator.
		Level	: 40 mV rms

•Set the modulation analyzer to the same condition as “MODULATION BALANCE.”

•Transmitting

(NARROW)		• Channel	: CH 8
[MOD N C]		• Transmitting
[MOD N L]	2	• Channel	: CH 9
		• Transmitting
[MOD N H]	3	• Channel	: CH 10
		• Transmitting
(WIDE)	4	• Channel	: CH 4			±4.05 to ±4.15 kHz
[MOD W C]		• Transmitting
[MOD W L]	5	• Channel	: CH 3
		• Transmitting
[MOD W H]	6	• Channel	: CH 2
		• Transmitting
(MIDDLE)*	7	• Channel	: CH 11			±3.15 to ±3.25 kHz
[MOD W C]		• Transmitting
[MOD M L]	8	• Channel	: CH 12
		• Transmitting
[MOD M H]	9	• Channel	: CH 13
		• Transmitting
DIGITAL	1	Set the preset value of [Digital Mode] to “7” on the adjustment software.
DAVIATION
	2	• Attach the UT-119 to J2.		Rear	Connect the modulation ana-	±1.41 to ±1.45 kHz
[MOD D C]
		(Refer to page 4-2 for the installation)		panel	lyzer to the antenna connector
		• Channel	: CH 14		through an attenuator.
		• Transmitting
[MOD D L]	3	• Channel	: CH 15
		• Transmitting
[MOD D H]	4	• Channel	: CH 16
		• Transmitting
CTCSS/DTCS	1	• Channel	: CH 17	Rear	Connect a modulation analyzer to	±0.68 to ±0.72 kHz
DEVIATION		• No audio signals applied to the JIG cable.		panel	the antenna connector through
[CTCS/DTCS]		• Set the modulation analyzer to the same			an attenuator.
		condition as “MODULATION BALANCE.”
		• Transmitting
2TONE,	1	• Channel	: CH 18	Rear	Connect a modulation analyzer to	±1.50 kHz
5TONE,		• Transmitting		panel	the antenna connector through
DTMF					an attenuator.
[S.Tone]
*; [EUR] only.

6 - 5