UT-112/UT-98 installation | Icom IC-M505 specs

9 CONNECTIONS AND MAINTENANCE

■UT-112/UT-98 installation

CAUTION: DISCONNECT the DC power cable from the

transceiver before performing any work on the transceiver.

Otherwise, there is danger of electric shock and/or equip- ment damage.

Follow the case opening procedure shown here when you want to install an optional scrambler unit.

qRemove the 6 screws as shown below and open the trans- ceiver.

wDisconnect the ﬂat cable and NMEA (4 pin) from J5 of the LOGIC unit.

LOGIC unit

NMEA (4 pin)

q

Flat cable

w

eInstall an optional unit (UT-112 or UT-98) to J3 on the AF unit as shown below.

Optional unit

J3

AF unit

62

Image 68

Icom IC-M505 instruction manual UT-112/UT-98 installation

Contents

IM505 Word Definition May occurEquipment damage may occur Personal injury, ﬁre or electric shock Case of Emergency DOC Iii Table of Contents Precautions Operating Rules Ship Station LicenseOPERATOR’S License Restricted Radiotelephone Operator Permit is the license Panel Description Front panel 2TRANSMIT Power KEY H/L 0TIME Zone Indicator Function display Microphone 1POSITION Indicator2SCAN Indicator Basic Operation Channel selectionChannel Call channel International channels Atis and DSC channelsThere are pre-programmed 57 international channels for IC-M505 Push H/L to select the output power if necessary Receiving and transmitting Call channel programming Channel comments Microphone Lock functionDisplay backlight NEL Push Channelenter Optional voice scrambler operationActivating the scrambler Programming scrambler codes Scan Operation Scan typesPriority Scan Normal Scan Starting a scan Setting TAG channelsClearing or setting all tagged channels DUALWATCH/TRI-WATCH DescriptionOperation DUALWATCH/TRI-WATCH Simulation DSC Operation Mmsi code programmingRotate Channel to select Mmsi Check, push Channelenter Rotate Channel to set the speciﬁc 9-digit Mmsi code Mmsi code check Check the 9-digit Mmsi DSC self ID code DSC address ID Programming Individual IDRotate Channel to select AddINDV ID, push Channelenter Rotate Channel to set the individual ID and ID name Rotate Channel to select the desired ID name for deleting Deleting Individual IDRotate Channel to select Delindv ID, push Channelenter Rotate Channel to set the group ID and ID name Programming Group IDRotate Channel to select AddGroup ID, push Channelenter Deleting Group ID Rotate Channel to select DELGroup ID, push Channelenter Position and time programming Position and time indication GPS information indication After 2 sec. Wait ACK Distress callSimple call Distress alert contains default Regular call Push Distress for 5 sec. to transmit the distress call Transmitting DSC calls Transmitting an individual call Push Channelenter to transmit the individual call Transmitting an individual acknowledgement Transmitting a group call Push Channelenter to transmit the group call Transmitting an all ships call Push Channelenter to transmit the all ships call Transmitting a position request call Push Channelenter to transmit the position request call Transmitting a position report call Push Channelenter to transmit the position report call Transmitting a polling request call Push Channelenter to transmit the polling request call Transmitting a position request reply call DSC Menu Position Reply Ready CLR˘Exit / ENT˘OK Transmitting a position report reply call Transmitting a polling request reply call Receiving DSC calls Receiving a distress callReceiving a distress acknowledgement Receiving a distress relay call Receiving an all ships call Receiving an individual callReceiving a group call Receiving a position report call Receiving a geographical area callReceiving a position request call Receiving a polling request call Receiving a position request reply callReceiving a position report reply call Receiving a polling request reply call Received messages Distress messageRotate Channel to select Distress, push CHAN- Nelenter Rotate Channel to scroll the message Other messages Rotate Channel to select Other, push CHAN- Nelenter Rotate Channel to select Offset Time, push Channelenter DSC Set modeNo offset time default Push Channelenter to set the condition Automatic acknowledgementRotate Channel to select Auto ACK, push Channelenter Nmea Output Rotate Channel to select Nmea Output, push Channelenter Intercom operation Push IC to enter Intercom modeOther Functions RX Speaker function Deck or tower via an external speaker or hailer speaker Able Push Hailrx to enter hailer mode Hailer operation Automatic foghorn function UnderwayStop Sail Selected foghorn SET Mode Set mode programmingSet mode items Scan resume timer Dual/Tri-watch Beep toneLCD contrast Automatic foghorn frequency Scrambler code Radio powerScrambler type Connections and Maintenance Connections Fuse replacement Supplied accessoriesAntenna Microphone hanger Using the supplied mounting bracket Mounting the transceiver That the clamps press firmly against the inside MB-75 installationTighten the end bolts on the clamps rotate clockwise so UT-112/UT-98 installation HM-162E installation Return the cables and screws to the original position Completed installation should look like this Gasket Troubleshooting Problem Possible Cause Solution Specifications and Options SpeciﬁcationsGeneral Receiver Transmitter For mounting the transceiver to a panel DimensionsOptions †Receive only Channel ListInternational channels Channel List Template 165 146 R12 Max92.4 110 29.5 to 31.5 d Cut here Unit mmPage Memo Intended Country of Use Kamiminami, Hirano-ku, Osaka 547-0003, Japan