Completed installation should look like this | Icom IC-M505 manual

9 CONNECTIONS AND MAINTENANCE

qInsert the supplied cable into the external microphone jack and tighten the cable nut as shown below.

wTo use the supplied cable as a wall socket, perform the fol- lowing steps.

eUsing the mounting base as a template, carefully mark the holes where the cable and three screws will be fastened.

rDrill holes at these marks.

tInstall the mounting base using the supplied screws as shown below.

Mounting base

Nut

Gasket
Screw holes
(approx. 2 (d) mm; 3 32″ )	Cap

yThe completed installation should look like this.

64

Image 70

Icom IC-M505 instruction manual Completed installation should look like this

Contents

IM505 Equipment damage may occur Word DefinitionMay occur Personal injury, ﬁre or electric shock Case of Emergency DOC Iii Table of Contents Precautions OPERATOR’S License Operating RulesShip Station License Restricted Radiotelephone Operator Permit is the license Panel Description Front panel 2TRANSMIT Power KEY H/L 0TIME Zone Indicator Function display 2SCAN Indicator 1POSITION IndicatorMicrophone Channel Basic OperationChannel selection Call channel There are pre-programmed 57 international channels for International channelsAtis and DSC channels IC-M505 Push H/L to select the output power if necessary Receiving and transmitting Call channel programming Display backlight Channel commentsMicrophone Lock function NEL Activating the scrambler Programming scrambler codes Optional voice scrambler operationPush Channelenter Priority Scan Scan OperationScan types Normal Scan Clearing or setting all tagged channels Setting TAG channelsStarting a scan Operation DUALWATCH/TRI-WATCHDescription DUALWATCH/TRI-WATCH Simulation Rotate Channel to select Mmsi Check, push Channelenter DSC OperationMmsi code programming Rotate Channel to set the speciﬁc 9-digit Mmsi code Mmsi code check Check the 9-digit Mmsi DSC self ID code Rotate Channel to select AddINDV ID, push Channelenter DSC address IDProgramming Individual ID Rotate Channel to set the individual ID and ID name Rotate Channel to select Delindv ID, push Channelenter Deleting Individual IDRotate Channel to select the desired ID name for deleting Rotate Channel to select AddGroup ID, push Channelenter Programming Group IDRotate Channel to set the group ID and ID name Deleting Group ID Rotate Channel to select DELGroup ID, push Channelenter Position and time programming Position and time indication GPS information indication Simple call Distress callAfter 2 sec. Wait ACK Distress alert contains default Regular call Push Distress for 5 sec. to transmit the distress call Transmitting DSC calls Transmitting an individual call Push Channelenter to transmit the individual call Transmitting an individual acknowledgement Transmitting a group call Push Channelenter to transmit the group call Transmitting an all ships call Push Channelenter to transmit the all ships call Transmitting a position request call Push Channelenter to transmit the position request call Transmitting a position report call Push Channelenter to transmit the position report call Transmitting a polling request call Push Channelenter to transmit the polling request call Transmitting a position request reply call DSC Menu Position Reply Ready CLR˘Exit / ENT˘OK Transmitting a position report reply call Transmitting a polling request reply call Receiving a distress acknowledgement Receiving DSC callsReceiving a distress call Receiving a distress relay call Receiving a group call Receiving an individual callReceiving an all ships call Receiving a position request call Receiving a geographical area callReceiving a position report call Receiving a position report reply call Receiving a polling request callReceiving a position request reply call Receiving a polling request reply call Rotate Channel to select Distress, push CHAN- Nelenter Received messagesDistress message Rotate Channel to scroll the message Other messages Rotate Channel to select Other, push CHAN- Nelenter No offset time default DSC Set modeRotate Channel to select Offset Time, push Channelenter Rotate Channel to select Auto ACK, push Channelenter Automatic acknowledgementPush Channelenter to set the condition Nmea Output Rotate Channel to select Nmea Output, push Channelenter Other Functions Push IC to enter Intercom modeIntercom operation RX Speaker function Deck or tower via an external speaker or hailer speaker Able Push Hailrx to enter hailer mode Hailer operation Stop Automatic foghorn functionUnderway Sail Selected foghorn Set mode items SET ModeSet mode programming Scan resume timer LCD contrast Dual/Tri-watchBeep tone Automatic foghorn frequency Scrambler type Radio powerScrambler code Connections and Maintenance Connections Antenna Fuse replacementSupplied accessories Microphone hanger Using the supplied mounting bracket Mounting the transceiver Tighten the end bolts on the clamps rotate clockwise so MB-75 installationThat the clamps press firmly against the inside UT-112/UT-98 installation HM-162E installation Return the cables and screws to the original position Completed installation should look like this Gasket Troubleshooting Problem Possible Cause Solution General Receiver Specifications and OptionsSpeciﬁcations Transmitter Options DimensionsFor mounting the transceiver to a panel International channels Channel List†Receive only Channel List 92.4 110 29.5 to 31.5 d Template165 146 R12 Max Cut here Unit mmPage Memo Intended Country of Use Kamiminami, Hirano-ku, Osaka 547-0003, Japan