HM-162E installation | Icom IC-M505 guide

rReturn the cables and screws to the original position.

• Be sure not upside down the ﬂat cable.

CAUTION:

• When re-assembling the case and tightening the screws,

you must keep the speciﬁed torque (0.5±0.07 N.m). Oth-

erwise the transceiver may be damaged (torque too high)

or lose waterproof efﬁciency (torque too low).

• When uninstalling the optional unit, remove it vertically.

Wiggling the unit from side to side may damage the op- tional unit's connector.

CONNECTIONS AND MAINTENANCE 9

■HM-162E installation

9

The optional HM-162E should be installed to the transceiver using the supplied connection cable.

The connector of the connection cable can be installed into a cabinet, wall, etc., as a built-in plug.

For longer distance remote operation, the optional extension cable, OPC-1541 (6 m; connecting between transceiver and the connection cable), is available, and up to two OPC-1541 can be added.

63

Image 69

Icom IC-M505 instruction manual HM-162E installation, Return the cables and screws to the original position

Contents

IM505 May occur Word DefinitionEquipment damage may occur Personal injury, ﬁre or electric shock Case of Emergency Iii DOC Table of Contents Precautions Ship Station License Operating RulesOPERATOR’S License Restricted Radiotelephone Operator Permit is the license Front panel Panel Description 2TRANSMIT Power KEY H/L Function display 0TIME Zone Indicator 1POSITION Indicator 2SCAN IndicatorMicrophone Channel selection Basic OperationChannel Call channel Atis and DSC channels International channelsThere are pre-programmed 57 international channels for IC-M505 Receiving and transmitting Push H/L to select the output power if necessary Call channel programming Microphone Lock function Channel commentsDisplay backlight NEL Optional voice scrambler operation Activating the scrambler Programming scrambler codesPush Channelenter Scan types Scan OperationPriority Scan Normal Scan Setting TAG channels Clearing or setting all tagged channelsStarting a scan Description DUALWATCH/TRI-WATCHOperation DUALWATCH/TRI-WATCH Simulation Mmsi code programming DSC OperationRotate Channel to select Mmsi Check, push Channelenter Rotate Channel to set the speciﬁc 9-digit Mmsi code Check the 9-digit Mmsi DSC self ID code Mmsi code check Programming Individual ID DSC address IDRotate Channel to select AddINDV ID, push Channelenter Rotate Channel to set the individual ID and ID name Deleting Individual ID Rotate Channel to select Delindv ID, push ChannelenterRotate Channel to select the desired ID name for deleting Programming Group ID Rotate Channel to select AddGroup ID, push ChannelenterRotate Channel to set the group ID and ID name Rotate Channel to select DELGroup ID, push Channelenter Deleting Group ID Position and time programming GPS information indication Position and time indication Distress call Simple callAfter 2 sec. Wait ACK Regular call Distress alert contains default Push Distress for 5 sec. to transmit the distress call Transmitting an individual call Transmitting DSC calls Push Channelenter to transmit the individual call Transmitting an individual acknowledgement Transmitting a group call Push Channelenter to transmit the group call Push Channelenter to transmit the all ships call Transmitting an all ships call Transmitting a position request call Push Channelenter to transmit the position request call Transmitting a position report call Push Channelenter to transmit the position report call Push Channelenter to transmit the polling request call Transmitting a polling request call Transmitting a position request reply call DSC Menu Position Reply Ready CLR˘Exit / ENT˘OK Transmitting a position report reply call Transmitting a polling request reply call Receiving a distress call Receiving DSC callsReceiving a distress acknowledgement Receiving a distress relay call Receiving an individual call Receiving a group callReceiving an all ships call Receiving a geographical area call Receiving a position request callReceiving a position report call Receiving a position request reply call Receiving a polling request callReceiving a position report reply call Receiving a polling request reply call Distress message Received messagesRotate Channel to select Distress, push CHAN- Nelenter Rotate Channel to scroll the message Rotate Channel to select Other, push CHAN- Nelenter Other messages DSC Set mode No offset time defaultRotate Channel to select Offset Time, push Channelenter Automatic acknowledgement Rotate Channel to select Auto ACK, push ChannelenterPush Channelenter to set the condition Rotate Channel to select Nmea Output, push Channelenter Nmea Output Push IC to enter Intercom mode Other FunctionsIntercom operation Deck or tower via an external speaker or hailer speaker Able RX Speaker function Hailer operation Push Hailrx to enter hailer mode Underway Automatic foghorn functionStop Sail Selected foghorn Set mode programming SET ModeSet mode items Scan resume timer Beep tone Dual/Tri-watchLCD contrast Automatic foghorn frequency Radio power Scrambler typeScrambler code Connections Connections and Maintenance Supplied accessories Fuse replacementAntenna Microphone hanger Mounting the transceiver Using the supplied mounting bracket MB-75 installation Tighten the end bolts on the clamps rotate clockwise soThat the clamps press firmly against the inside UT-112/UT-98 installation Return the cables and screws to the original position HM-162E installation Completed installation should look like this Gasket Problem Possible Cause Solution Troubleshooting Speciﬁcations Specifications and OptionsGeneral Receiver Transmitter Dimensions OptionsFor mounting the transceiver to a panel Channel List International channels†Receive only Channel List 165 146 R12 Max Template92.4 110 29.5 to 31.5 d Cut here Unit mmPage Memo Kamiminami, Hirano-ku, Osaka 547-0003, Japan Intended Country of Use