PART | R0399A |
Note: To identify the parts listed below, refer to the EXPLODED DRAWING attached at the center of this manual.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Frame | 53 | 2 | Sensor Wire |
2 | 55 | Screw | 54 | 2 | Shock |
3 | 5 | Isolator Nut | 55 | 1 | Walking Belt |
4 | 4 | Spring Bolt | 56 | 8 | Belly Pan Spacer |
5 | 2 | Cushion Spring | 57 | 5 | Motor Pivot Nut |
6 | 2 | Isolator | 58 | 1 | Cushion Shaft |
7 | 2 | Cushion Adj. Rack | 59 | 1 | Belly Pan |
8 | 8 | Rack Screw | 60 | 1 | Right Foot Rail |
9 | 2 | Cushion Adj. Gear | 61 | 5 | 8” Cable Tie |
10* | 1 | Motor/Pulley/Flywheel/Fan | 62 | 1 | Motor Bracket |
11 | 1 | Latch Housing | 63 | 1 | Tie Holder |
12 | 1 | Left Foot Rail | 64 | 1 | Releasable tie |
13 | 2 | Rear Platform Screw | 65 | 2 | Short Rear Roller Adj. Bolt |
14 | 2 | Roller Guard | 66 | 1 | Rear Roller Endcap |
15 | 1 | Walking Platform | 67 | 2 | Endcap Pad |
16 | 1 | Rear Roller | 68 | 1 | Pulse Monitor |
17 | 4 | Incline Pivot Bolt/Incline Motor Nut | 69 | 1 | Monitor Strap |
18 | 1 | Front Roller/Pulley | 70 | 1 | Console |
19 | 4 | Motor Bolt | 71 | 19 | Upright Cap Screw |
20 | 1 | Console Base | 72 | 1 | Motor |
21 | 5 | Bracket Screw | 73 | 4 | Upright Cap |
22 | 2 | Hood Anchor | 74 | 8 | Console Screw |
23 | 2 | Hood Anchor Bracket | 75 | 1 | Console Plate |
24 | 3 | Motor Bracket Bolt | 76 | 1 | Pulley/Flywheel/Fan |
25 | 3 | Motor Bracket Washer | 77 | 1 | Hood |
26 | 3 | Long Hood Bracket | 78 | 5 | Hood Screw |
27 | 2 | Belt Guide | 79 | 1 | Cushion Knob |
28 | 2 | Motor Tension Bolt | 80 | 1 | Power Board |
29 | 1 | Outlet Bracket | 81 | 4 | Plastic |
30 | 1 | Circuit Breaker | 82 | 1 | Set Screw |
31 | 1 | Power Cord | 83 | 1 | Controller |
32 | 1 | Power Cord Grommet | 84 | 1 | Upright Wire Harness |
33 | 1 | On/Off Switch | 85 | 2 | Isolator Bolt |
34 | 1 | Incline Leg | 86 | 1 | Electronics Plate |
35 | 1 | Front Roller Adj. Bolt | 87 | 1 | Upright Cover (right inside) |
36 | 9 | Roller Adj. Washer | 88 | 2 | Upright Cover |
37 | 2 | Incline Leg Spacer | 89 | 2 | Platform Screw (front) |
38 | 3 | Incline Leg Pivot Nut | 90 | 2 | Wheel Bolt |
39 | 4 | Motor Nut | 91 | 4 | Front Wheel |
40 | 1 | Motor Pivot Bolt | 92 | 1 | 8” Ground Wire |
41 | 2 | Roll Pin | 93 | 9 | Wheel Nut |
42 | 1 | Key/Clip | 94 | 1 | Adhesive Clip |
43 | 2 | Flange Nut | 95 | 1 | Allen Wrench |
44 | 2 | Motor Tension Washer | 96 | 2 | Upright Cap |
45 | 2 | Small Nut | 97 | 2 | Handrail Foam |
46 | 1 | 4” Wire Tie | 98 | 2 | Handrail Endcap |
47 | 2 | Small Bolt | 99 | 1 | Lock Knob |
48 | 2 | Sensor | 100 | 1 | Lock Knob Sleeve |
49 | 1 | Speed Sensor Bracket | 101 | 1 | Lock Knob Spring |
50 | 1 | Speed Disk | 102 | 1 | Lock Pin Collar |
51 | 1 | Motor Belt | 103 | 1 | Lock Pin |
52 | 1 | Warning Decal | 104 | 1 | Pin Clip |
22
