The programmer
Programmer knob 
to display a symbol, turn the knob
to select a symbol, press the knob
to set the various display, setting the clock and timer, total cooking time and end time
Turn the knob
Clock :
The time of day is always shown
also used to temporarily show the end of time of an operation
Symbol
is used to set the
end time for a cooking or pyrolysis operation
Symbol 
is used to set the total cooking or pyrolysis time (duration)
for increasing numbers
for decreasing
numbers
Symbol | Symbol |
is used for operating | is used to set the clock |
the audio timer |
|
The “24 hour” electronic programmer enables the user to set the duration and end time of a cooking operation for any time within the upcoming 24 hours.
You can check the end time 
, the cooking time 
and the timer 
simply by turning the programmer knob to select the corresponding symbol.
•Setting the clock:
When the appliance is turned on for the first time or after
a power cutoff, the clock display and the 
indicator light are flashing. Turn the programmer knob until the desired time is shown. After 3 seconds, the time is vali- dated.
To modify the time, the oven must be in manual mode (no indicator lights on). Press and hold the programmer
knob until the 
indicator light starts flashing. Then turn the knob to display the desired time.
•Audio timer:
To use the audio signal timer built into your oven, display
the 
(hourglass) symbol by turning and pressing the programmer knob. Then turn until the desired time is dis- played. As soon as you release the knob, the timer will start to count down. When the time is up, an audio signal sounds. Press the knob to turn off the signal. The timer operates independently from the oven.
Cooking without the Programmer (manual mode) When no symbol is lit, the oven is in manual mode.
- Use the Function Selector to choose the desired cook- ing method. A preselected temperature appears. You can change it using the Temperature Selector.
The 
indicator light flashes slowly while the temperature in the oven is rising. It stays on when the temperature reaches the specified level.
When the cooking is done, remember to turn off the oven by setting the Function Selector back to “0”.
Programmed cooking
1 - Immediate start
The oven starts heating immediately and stops automati- cally at the end of the programmed time.
- Display the cooking time:
Turn the programmer knob to select the 
indicator light.
Press the knob. 
flashes. Turn the knob to display the desired cooking time. After 3 seconds, your choice is vali-
dated. | remains on at half power. | |
(Ignore the flashing of the | light.) | |
-Set the Function Selector to the desired position
-If desired, change the temperature using the Temperature Selector.
•To cancel the cooking time, select the 
function. Press and turn the programmer knob to display 0.00.
•When the time is up, an audio signal sounds. To turn off the signal, press the knob and set the Function Selector back to “0”.
2 - Delayed start
The programmer automatically starts the oven at the programmed time.
-Make sure that the clock is set to the right time
-To display the cooking time:
Select the 
indicator light, then press the knob. 
flashes. Turn the knob to select the desired cooking time, such as 1:30 for example.
The 
indicator light flashes. Turn the knob to select the end time for the cooking operation (12:30, for example). Your choice is validated after 3 seconds.
The two indicator lights 
and 
remain on at half power.
-Set the Function Selector to the desired position.
-If desired, change the temperature using the Temperature Selector.
At 11:00, the cooking starts.
-To change the end time, proceed as follows:
Select the 
indicator light. Press the knob. 
flashes. Select the desired end time (for example, 12:30). After 3 sec- onds, the time of day reappears.
•When the time is up, an audio signal sounds. To turn off the signal, press the knob and set the Function Selector back to “0”.
7GB
