Converter Box with Analog Pass Through
Troubleshooting
Insignia has detailed information about troubleshooting problems on its Web site at:
Problem | Solution | |
|
| |
No power. | • Make sure that the power cord is | |
|
| plugged securely into a power outlet. |
|
| |
Fragmented picture | • Check your antenna input, location, | |
and unclear sound. |
| and signal strength. |
|
| |
No picture. | • Select the Auto Tuning or Manual | |
|
| Scan functions, if you have not |
|
| already done so. |
| • Make sure that all the cables are | |
|
| installed correctly and that the |
|
| correct source is selected on your TV |
|
| (for example, CH 3, CH 4, Video 1, or |
|
| Video 2). |
| • The antenna signal strength may be | |
|
| low. Check the signal strength and |
|
| adjust the antenna location and |
|
| direction. |
| For more information about connections, | |
| see “Connecting an antenna” on page 5. | |
|
|
|
Normal picture but | • | Check volume levels. |
no sound. | • Make sure that the TV sound is not | |
|
| muted. |
| • Make sure that the your converter | |
|
| box is connected correctly. |
|
| |
Picture is distorted. | • Make sure that the correct aspect | |
|
| ratio is selected. |
| • Make sure that the video output is | |
|
| connected to the TV. |
|
| |
Available channels | • You can find all the available | |
are missing. |
| channels by running the Auto Tuning |
|
| or EZ Add in the |
|
| system. |
| • | Adjust the antenna. |
| • Check the antenna’s signal strength. | |
|
| |
You forgot your | Enter the master password 7777. | |
password. |
|
|
|
| |
The remote control | • Point the remote control at the | |
does not work |
| remote sensor on your converter |
correctly. |
| box. |
| • Operate the remote control within | |
|
| 23 feet (7 meters) of the remote |
|
| sensor. |
| • Remove any obstacles between the | |
|
| remote control and the remote |
|
| sensor. |
| • Replace dead batteries with new | |
|
| ones. |
Specifications
Design and specifications are subject to change without prior notice.
General
Television system | DTV standard ATSC |
|
|
Channel coverage | Terrestrial |
|
|
Dimensions (W × H × D) | Approximately 8.5 × 1.8 × 6.4 inches |
| (215 × 46 × 162 mm) |
|
|
Net weight | Approximately 1.65 lbs. (0.75 kg) |
|
|
Operating temperature | 41°F to 104°F (5°C to 40°C) |
|
|
Operating humidity | 5% to 90% |
|
|
Power requirement | 120V 60 Hz AC |
|
|
Power consumption | 7 W |
Input/output |
|
|
|
Antenna in | Antenna input, ATSC, 75 ohms |
(From Antenna) |
|
|
|
Antenna out (To TV (RF)) | Antenna output, 75 ohms, RF output |
| channel 3 or 4 (switchable) |
|
|
Video output | 1.0 V |
| RCA jack (1) |
|
|
Audio output | 2.0 Vrms (1 KHz, 0 dB), 600 ohms, |
| RCA jack (L, R) (1) |
Legal notices
FCC warning
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the product and
•receiver.
•Connect the product into an outlet on a circuit different
•from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician
•for help.
Warning
Do not attempt to modify your converter box in any way without written authorization from Insignia. Unauthorized modification could void the user’s authority to operate this product.
Your converter box is intended to receive and decode signals transmitted according to the ATSC Digital Television Standard A/53 specification and is intended to be used with an appropriate antenna and display device that you must provide.
Energy Star ®
As an Energy Star Partner, Insignia has determined that this product or product models meet the Energy Star guidelines for energy efficiency.
18 |
