Insignia NS-LCD26A manual 25

Insignia NS-LCD26A LCD TV

6 Repeat steps 1 to 5 for the other devices you		6 To check for other device codes, repeat steps
	want to control. For future reference, write	1 to 5, substituting the device key for DVD.
	down each working device code below:	Changing Volume Lock
	AUX Code:
		The remote comes preset to allow independent
	CBL Code:
		volume control of each selected device (Global
	CD Code:
		Volume Unlock). However, you may change the
	DVD Code:	Volume Lock setting to Global Volume Lock so
	SAT Code:	that one device's volume will control volume in
		all other modes. After that, you can perform
	TNR Code:
		Individual Volume Unlock on a selected device to
	VCR Code:	set its volume control for independent operation
		or Global Volume Unlock to remove all volume
7 Press SET to save your code and exit setup.
		locking.
Searching for your code		To lock volume control to one mode (Global
If your device does not respond to the remote		Volume Lock):
		1 Press and hold SET until the red LED blinks
after trying all codes listed for your brand, or if
your brand is not listed, try searching for your		twice, then release the button.
code:		2 Enter 9-9-3and then press the mode key for
1 Press a device key once.		the device you want to control volume (for
2 Press and hold SET until the red LED blinks		example, DVD). The LED blinks twice. Now
		when you press VOL+, VOL-, or Mute, the
	twice; then release.
		selected device (for example, DVD) will
3 Enter 9-9-1, then the device group number
		control the volume regardless of the current
	(0= Cable, 1= TV, 2= VCR, 3= Audio). The	mode.
	LED blinks twice.	To unlock all volume control (restoring
4 Aim the remote at the device and press
		Global Unlock):
	Power. The remote sends IR codes from its
		1 Press and hold SET until the red LED blinks
	library to the selected device, starting with
	the most popular code first. If the device	twice, then release the button.
	responds, go to step 7.	2 Enter 9-9-3and then press VOL+. The LED
5 If the device does not respond, press CH+.		blinks four times. Volume is now
	The remote will try the next code. Continue	independently controlled for all programmed
	until the device responds.	devices.
		To unlock a single device's volume control:
	Note
		1 Press a device key (DVD, CBL, or AUX).
	Press CH- to try the previous code.
		2 Press and hold SET until the red LED blinks
6 To search for other device codes, repeat
		twice, then release the button.
	steps 1 to 5.
		3 Enter 9-9-3and then press VOL-. The LED
7 Press SET to save your code and exit setup.
		blinks four times. Volume is now
Checking the Codes		independently controlled for the selected
		devices.
If you have set up the remote using the
		Troubleshooting
procedure in “Searching for Your Code” you may
need to find out which four-digit code is
operating your equipment.
		Problem	Solution
To find out which code is assigned to your
		LED does not blink	Replace new batteries.
DVD:
		when you press a key.
1 Press DVD once.
		LED blinks when you	Make sure the remote is aimed at your
2 Press and hold SET until the red LED blinks		press a key, but device	device and is not more than 15 feet away.
	twice, then release the button.	does not respond.
3 Enter 9-9-0. The LED blinks twice.		LED blinks one long	An entry error has occurred (for example,
4 To view the code for the first digit, press 1.		blink.	wrong key). Try the entry sequence again.
		Remote does not	Try all listed codes for the device. Make
	Count the LED blinks (for example, three
	blinks = 3), and write down the number in the	control devices or	sure the device operates with an infrared
		commands are not	remote control.
	appropriate code listing in step 6 under
		working properly.
	“Programming a Device”

Note

If a code digit is 0, the LED does not blink.

5Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.

Care

•Keep the remote dry. If it gets wet, wipe it dry immediately.

•Use and store the unit only in normal temperature environments.

•Handle the remote gently and carefully. Don't drop it.

www.insignia-products.com 23