Insignia
Programming the volume lock
The remote control comes preset to let you control the volume of each connected device. You can change the volume lock so that one device’s volume controls volume in all modes.
After you lock the volume control, you can unlock the volume control for a specific device so you can control the volume for that device independently.
To lock the volume control:
1Press and hold the SET button until the LED blinks twice, then release the button.
2Enter 993, then press the device button for the device you want to control the volume. The LED blinks twice. When you press the VOL+,
To unlock the volume control:
1Press and hold the SET button until the LED blinks twice, then release the button.
2Enter 993, then press VOL+ button. The LED blinks four times. The volume control is unlocked.
To unlock a single device’s volume control:
1Press the device key.
2Press and hold the SET button until the LED blinks twice, then release the button.
3Enter 993, then press VOL– button. The LED blinks four times. The volume control for the device you selected is unlocked.
Troubleshooting the remote control
Symptom | Possible solution |
|
|
LED does not blink when | Replace the batteries. |
a button is pressed |
|
|
|
LED blinks when a | Make sure that you are at less than 15 |
button is pressed, but | feet (4.6 meters) from the device and |
device does not respond | that you point the remote control at the |
| remote sensor on the device. |
|
|
LED blinks one long | You pressed an incorrect button. Start |
blink | the procedure over again. |
|
|
Remote control does not | Make sure that the device has a remote |
control a device or only | sensor, then try another code. |
controls some features |
|
of the device |
|
|
|
No volume on a device | See “Programming the volume lock” |
| on page 18. |
Maintaining
•Do not use your TV in areas that are too hot or too cold because the cabinet may warp or the screen may malfunction.
•Storage temperatures are 32° to 122°F (0° to 50°C).
•Working temperatures are 41° to 104°F (5° to 40°C).
•Do not place your TV in direct sunlight or near a heat source.
Cleaning your TV
Clean the screen and cabinet with a soft,
Caution
Avoid volatile substances, such as insect sprays, solvents, and thinners.
Do not leave your TV in contact with items made from rubber or PVC for long periods.
They may damage your TV.
Caution
Do not let liquids drip into the cabinet.
Troubleshooting
Warning
Do not try to repair your TV yourself. Refer all service to a qualified service technician.
Symptom | Possible solution |
|
|
No power | • Make sure that the power cord |
| is connected to your TV and an |
| electrical outlet. |
| • Unplug the power cord, wait 60 |
| seconds, then plug the cord |
| back in and turn on your TV. |
|
|
No picture | • Make sure that the video cables |
| are connected securely to the |
| back of your TV. |
| • Adjust the contrast and |
| brightness. |
| • Make sure that the correct |
| video mode is selected. |
| • Make sure that the incoming |
| signal is compatible. |
|
|
Good picture but no | • Increase the volume. |
sound | • Make sure that the sound is not |
| muted. |
| • Make sure that the correct |
| audio mode is selected. |
|
|
Good sound but poor | • Adjust the contrast, color, and |
color | brightness settings. |
|
|
Poor picture | • Make sure that the room is not |
| too bright. Light reflecting off |
| the screen can make the picture |
| difficult to see. |
| • If an |
| camcorder is connected while |
| another connected device is |
| turned on, the picture may be |
| poor. Turn off one or more |
| devices. |
18 |
