Insignia NS-MDDVD10 Dual-Screen Portable DVD Player

Number

Remote control

Function

Connecting AC power

The AC adapter operates using AC power

15

Angle button

Switch between multiple

between 100 and 240 volts.

 

 

camera angles when the

 

 

Note:

 

 

DVD playing has multiple

 

 

camera angles recorded.

Before operating the DVD player in a new area for the first

16

Audio button

Select one audio sound

time, you must check that the operating voltage of your DVD

player is identical to the voltage of your local power supply.

 

 

tracks programmed on a

This DVD player is to be operated only at the power source

 

 

DVD or select audio output

voltage printed on the back panel. Disconnect from the

 

 

mode on an AUDIO CD.

power outlet when not in use for a long period of time.

17

Subtitle/Return button

Select one of the subtitle

To connect the AC adapter:

 

 

languages programmed on a

 

 

 

DVD or return to the normal

 

 

 

operation after using the

 

 

 

SETUP menu of a DVD.

 

Setting up your DVD player

Preparing the remote control

Installing remote control battery

Warning Do not throw the battery into fire. Dispose of used batteries as hazardous waste.

Built-in DIN cable

 

AC power cord

Power indicator

on AC adapter

1Connect the built-in DIN cable from the bottom of the monitor to the Main Unit port on the DVD player.

Caution Do not drop or disassemble the remote control. Do not get the remote control wet.

2Connect the plug end of the AC adapter to the DC In 9V/Car Plug - 12V jack on the DVD player.

To install the battery in the remote control:

1Remove the battery holder.

2Insert one CR2025 (3-volt) battery into the battery compartment. Make sure that the +/– symbols on the battery match the +/– marks shown on the battery holder.

3Slide the battery cover into the remote control.

4Remove the PVC sheet before operating the remote control.

5Point the remote control at the remote sensor on the DVD player. The effective distance for remote operation is about 16 feet (5 meters).

Note:

When the remote control will not be used for a long period of time or when the battery is worn out, remove the battery to prevent leakage.

Note:

When using the remote control and you are required to move closer to the stereo for the remote control to operate, replace the battery. The remote control may not operate correctly if direct sunlight or the light of a high-frequency fluorescent lamp enters the remote control light sensor. In this case, change the system installation position to prevent the problem.

3Connect the AC power cord to the AC adapter.

4Connect the AC power cord to an AC outlet. When the power cord is connected to the AC outlet, the power indicator will be on even if the DVD player is turned off.

Connecting DC power

The car power adapter operates in vehicles with a 12-volt, negative-ground electrical system.

Warning

Disconnect the car power adapter when not in

 

use.

 

Do not use this system in vehicles with 24-volt

 

systems.

 

• Use this unit only with the included car

 

Caution

 

power adapter. Using another car adapter

 

could damage the unit or your vehicle.

 

• The 12V car power adapter included is for

 

use with this unit only. Do not use it with

 

any other equipment.

 

• In the interest of traffic safety, drivers

 

should not operate the unit or view videos

 

while driving.

 

• When the inside of the cigarette lighter

 

socket is dirty with ashes or dust, the

 

power section may become hot due to

 

poor contact. Be sure to clean the

 

cigarette lighter socket before use.

 

• After use, disconnect the car power

 

adapter from both the unit and cigarette

 

lighter socket.

 

• If the unit is not properly attached to a

 

vehicle, it may become airborne in the

 

event of an accident and cause damage,

 

injury, or death.

 

• Check local traffic laws for rules

 

governing use of video devices in vehicles

 

before using this unit in your vehicle.

 

 

www.insignia-products.com

7