Rear panel description, Video In/Out, Monitor Out

Rear panel description

Depending on the impedance of the speakers used, set the SPEAKER IMPEDANCE SELECTOR on the rear panel as shown in the table.

Usable speaker impedance

Selector position

A or B speaker

4 ohms or higher/speaker

A and B speakers

8 ohms or higher/speaker

A or B speaker

8 ohms or higher/speaker

AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

•Do not use a power cord other than the one supplied with the DTM-5.3. The power cord supplied is designed for use with the DTM-5.3 and should not be used with any other device.

•Never disconnect the power cord from the DTM-5.3 while the other end is plugged into a wall outlet. Doing so may cause an electric shock. Always connect by plugging into the wall outlet last and disconnect by unplugging from the wall outlet ﬁrst.

AC INLET

Power cord (supplied)

To an AC wall outlet

AC OUTLET

The DTM-5.3 is supplied with AC mains outlet for connect- ing the power cords from other devices so that their power is supplied through the DTM-5.3. By doing this, you can use the Standby/On button on the DTM-5.3 to turn on and off the connected devices as well.

Caution:

Make sure that the capacity of the other components con- nected to this unit does not exceed the 120 watts.

AC INLET

AC OUTLET

AC 120V 60 Hz SWITCHED

120W 1 A MAX.

Other component

SPEAKERS terminals

Connect the left and right speakers here.

VIDEO IN/OUT

The DTM-5.3 provides two video inputs and one video out- put. Connect a DVD player, VCR, or other video player to the input and connect a VCR or other video recorder to the output.

AUDIO IN/OUT

There are 6 audio inputs and 3 audio outputs for use with ana- log signals. The audio inputs and outputs require RCA type connectors.

•When connecting a VCR or other video component, make sure you connect the audio and video leads together (i.e., both to VIDEO).

•The PHONO jacks are designed for use with turntables that use moving magnet cartridges.

MONITOR OUT

This output enables you to connect to a television monitor.

SUB WOOFER PRE OUT

This terminal enables you to connect to an active subwoofer.

Note: The subwoofer can only operate when speaker system A is turned on.

REMOTE CONTROL

The terminal on the DTM-5.3 enables you to connect to other Integra/Onkyo components equipped with the same

terminal. When a component is -connected, you can point the remote controller supplied with the DTM-5.3 at the sensor on the DTM-5.3 and operate that component without having to switch remote controllers.

In addition, by connecting components to the terminal, you can also perform the system operations given below.

Power on/ready function

When the DTM-5.3 is in Standby mode, if an -connected component is turned on, then the DTM-5.3 also turns on and the input source selected at the DTM-5.3 automatically switches to that component.

If the power cord for an -connected component is con- nected to the AC OUTLET on the DTM-5.3, or if the DTM- 5.3 is turned on, this function will not work.

Direct change function

When the play button is pressed on an -connected compo- nent, the input source selected at the DTM-5.3 automatically changes to that component.

Power off function

When the DTM-5.3 is placed in Standby mode, all -con- nected components are also automatically placed in Standby mode.

DTM-5.3

connector

Ex: Integra/Onkyo CD player

connector

Ex: Onkyo cassette tape deck

To connect components using the terminal, simply con-

nect a remote control cable from this terminal to the

terminal of the other component. An remote control cable with a 1/8-inch (3.5mm) miniature two-conductor plug comes with every cassette tape deck, compact disc player,