Integra DTR-7.2 instruction manual Connections, Connecting a video cassette recorder VIDEO

Connections

S Video input
Video input
Analog audio	L (white)
input
	R (red)

6. VCR (VIDEO 1)

	R (red)
Analog audio
output	L (white)
Video output
S Video output

DIGITAL		PR	AUDIO	VIDEO	S VIDEO	COMPONENT
OUTPUT		RENNA				VIDEO
	FRONT
					MONITOR	OUTPUT
OPT					OUT	Y
			R	L
	SUB
DIGITAL			AM	OUT	ZONE 2	PB
INPUT
COAX	SURR
1				IN	DVD	PR
	SURR					INPUT 1
	BACK
2			FM	OUT		Y
			75
					VIDEO 1
3	FRONT			IN		PB
		O
OPT	SUB	L
1			PH	OUT		PR
	SURR				VIDEO 2	INPUT 2
2			CD	IN		Y
	SURR		OUT
	BACK
3				IN	VIDEO 3	PB

RTAPE

DIGITAL			IN		VIDEO 4	PR
INPUT
GND	L	IN	L
		R		VIDEO	S VIDEO
	O		AUDIO

7.Settop box, video camera (VIDEO 3)

R (red)
	Analog audio
L (white)	output

Video output

S Video output

Digital audio output (optical)

With the initial settings of the DTR-7.2, the DVD input source is set for digital input at the COAX 1 jack.

If the digital connection is made at a different jack, this must be changed at the Setup menu: Input Setup → Digital Setup (see page 34).

5.Connecting a DVD recorder or other digital video recording device (VIDEO 2) (see page 17)

Using an RCA-type video connection cable, connect the video output terminal (composite) on the device to the VIDEO 2 IN jacks on the DTR-7.2 and video input terminal to the VIDEO 2 OUT jacks. If there is an S video input/output terminal on the device, connect it to the S VIDEO 2 IN/OUT jack using an S video cable. You do not need to connect to both the S VIDEO 2 IN and VIDEO 2 IN terminals. If the device has component video outputs, connect them to one of the COMPONENT VIDEO INPUT jacks.

With the initial settings of the DTR-7.2, the VIDEO 2 input source is set for the COMPONENT VIDEO INPUT 2 jack.

If the video connection is made at COMPONENT VIDEO INPUT 1, this must be changed at the Setup menu: Input Setup → Video Setup

→Component Video (see page 36).

Using an RCA-type audio connection cable, connect the audio output terminal on the device to the same VIDEO 2 IN audio jacks on the DTR-7.2 and audio input terminal to the VIDEO 2 OUT audio jacks. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a digital output jack as well, be sure to also connect it to either a DIGITAL INPUT (COAX) or DIGITAL INPUT (OPT) jack on the DTR-7.2 depending on the type of connector on the device.

With the initial settings of the DTR-7.2, the VIDEO 2 input source is set for digital input at the COAX 3 jack.

If the digital connection is made at a different jack, this must be changed at the Setup menu: Input Setup → Digital Setup (see page 34).

If the device also has a digital input jack, it can be connected to the DIGITAL OUTPUT (OPT) jack on the DTR-7.2 for digital recording of the source for Rec Out at the DTR-7.2.

Note:

The output from the DIGITAL OUTPUT jack of the DTR-7.2 is only the digital signal input to the DIGITAL INPUT jack.

6. Connecting a video cassette recorder (VIDEO 1)

Using an RCA-type video connection cable, connect the video output terminal (composite) on the video cassette recorder to the VIDEO 1 IN jacks on the DTR-7.2 and video input terminal to the VIDEO 1 OUT jacks. If there is an S video input/output terminal on the video cassette recorder, connect it to the S VIDEO 1 IN/OUT jack using an S video cable. You do not need to connect to both the S VIDEO 1 IN and VIDEO 1 IN terminals. If the video cassette recorder has component video outputs, connect them to one of the COMPONENT VIDEO INPUT jacks.

With the initial settings of the DTR-7.2, the VIDEO 1 input source is set for the COMPONENT VIDEO INPUT 2 jack.

If the video connection is made at COMPONENT VIDEO INPUT 1, this must be changed at the Setup menu: Input Setup → Video Setup

→Component Video (see page 36).

Using an RCA-type audio connection cable, connect the audio output terminal on the video cassette recorder to the same VIDEO 1 IN audio jacks on the DTR-7.2 and audio input terminal to the VIDEO 1 OUT audio jacks. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

With the initial settings of the DTR-7.2, the VIDEO 1 input source is set for digital input at the COAX 2 jack.

If the digital connection is made at a different jack, this must be changed at the Setup menu: Input Setup → Digital Setup (see page 34).

18