Connecting the power
Standby/On
Standby indicator
ON 
STDBY
RCVR 
Standby/On
Standby |
Power
On Off
Upsampling
Phones
Power
|
|
| Display | Dimmer |
|
|
|
|
|
| Rec Out | Zone 2 | Off |
| Master Volume | |
|
|
|
|
|
|
|
|
|
|
|
|
| Setup |
|
|
|
|
|
|
|
|
|
|
|
|
| Tuning |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Enter |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Return |
|
|
|
|
|
|
|
|
|
|
|
|
| Preset |
|
|
|
|
|
|
|
|
| Direct | Stereo | Surround | THX | DSP |
| FM Mode | Memory |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Clear |
|
|
|
|
|
|
| Zone 2 (GRN ) |
|
|
|
|
|
|
|
|
|
|
|
| Video 5/Video Cam Input |
| |
Audio | Rec ( RED ) | DVD | Video 1 | Video 2 | Video 3 | Video 4 | Video 5 | Tape | FM | AM | Phono | CD |
|
| ||
Selector |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VCR 1 | VCR 2 |
|
|
|
|
|
|
|
| Digital | S Video | Video | L Audio R |
Tape
To wall outlet
HOME THEATER CONTROLLER
•The 
ON ). When the power cord is plugged in for the first time, the
•Before you plug in the
•Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit.
To change the display of the input source from TAPE to MD:
If you connected an MD recorder to the TAPE jack on the
Changing the display:
Press and hold down the Tape source button until the display changes from TAPE to MD (approx. 3 seconds).
Tape
1.Plug the power cord into an AC wall outlet.
2.Press the Power switch to set the
The Standby indicator will light up.
3.Press the Standby/On button to turn on the
If you press the Standby/On button again, the receiver returns to Standby mode.
Standby
Power
On 
Off
Standby/On
Standby
Turn off
To return the display to its original setting, perform the same procedure. This setting is necessary to allow z system functions for the connected cassette tape or MD recorder.
Memory preservation
This unit does not require memory preservation batteries. A built- in memory power backup system preserves the contents of the memory during power failures and even when the Power switch is set to off. The Power switch must be set to on in order to charge the backup system.
Turning the power on from the remote controller:
Before you can use the remote controller, you must perform steps 1 and 2 above and place the
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
2. Press the ON button to turn on the
To return the
The memory preservation period after the unit has been turned off varies depending on climate and placement of the unit. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been turned off. This period is shorter when the unit is exposed to a highly humid climate.
26
