Intel 8S661FXMP-RZ , ,

- 30 -8S661FXMP-RZ Motherboard

English

System After AC Back

Off When AC-power back to the system, the system will be in "Off" state.

(Default Value)

On When AC-power back to the system, the system will be in "On" state.

Laststate When AC-power back to the system, the system will return to the Last state

before AC-power off.

IRQ [3-7, 9-15], NMI

When IRQ [3-7, 9-15] or NMI triggered, the suspend timer will be reloaded to prevent system from

getting into green mode.

Disabled Disable this function.

Enabled Enable this function. (Default value)

ModemRingOn

Disabled Disable Modem Ring on function.

Enabled Enable Modem Ring on function. (Default Value)

PME Event Wake Up

Disabled Disable this function.

Enabled Enable PME Event Wake up. (Default Value)

Power On by Keyboard

Any Key Set Keyboard power on by any key.

Password Input password (from 1 to 8 numbers) and press Enter to set the Keyboard

Power On Password.

Disabled Disable this function. (Default Value)

Power On by Mouse

Enabled Enable Power On by Mouse function.

Disabled Disable this function. (Default Value)

Resume by Alarm

You can enable Resume by Alarm and key in month/date/time to turn on system.

Disabled Disable this function. (Default Value)

Enabled Enable alarm function to POWER ON system.

If Resume by Alarm is Enabled.

Month Alarm : NA, 1~12

Day (of Month) : 0~31

Time (hh: mm: ss) : (0~23) : (0~59) : (0~59)

Power LED in S1 state

Blinking The Power LED will be blinking during S1 state. (Default value)

Dual/OFF The Power LED will be turned off or change color.

Contents

Main 8S661FXMP-RZ User's Manual Intel Pentium 4 Processor Motherboard Rev. 1002 12ME-661FXMPRZ-1002 Page Preparing Your Computer Installing the motherboard to the chassis Table of Content Chapter 1 Introduction Features Summary Page Introduction- 7 - 8S661FXMP-RZ Motherboard Layout 8S661FXMP-RZ Block Diagram Hardware Installation Process Step 2 Step 1 Step 3 Step 1: Install the Central Processing Unit (CPU) Step 1-1: CPU Installation Step 1-2: CPU Cooling Fan Installation Step 2: Install memory modules Step 3: Install expansion cards Step 4: Install I/O Peripherals Cables Step 4-1: I/O Back Panel Introduction Step 4-2: Connectors Introduction 3) CPU_FAN (CPU FAN Connector) 1/2) ATX_12V/ATX (Power Connector) 4) SYS_FAN (System FAN Connector) 5) FDD (Floppy Connector) 6) IDE1/ IDE2 (IDE1/IDE2 Connector) - 16 - 8S661FXMP-RZ Motherboard 8) F_PANEL (2x10 pins connector) 7) SATA0/SATA1 (Serial ATA Connector, Controlled by SiS964) 9) BAT (Battery) CAUTION + 10)F_AUDIO (Front Audio Panel Connector) 11)CD_IN (CD In Connector) 12) SPDIF_IO (SPDIF In/Out) 13)SUR_CEN 14)F_ USB1 / F_USB2 (Front USB Connectors) 16)COMB (COMB Connector) 15)CI (Chassis Intrusion, Case Open) Page Chapter 2 BIOS Setup CONTROL KEYS ENTERING BIOS Setup Main Menu Status Page Setup Menu / Option Page Setup Menu Page Standard CMOS Features Date Time IDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Page Advanced BIOS Features Boot Up Floppy Seek Page Integrated Peripherals IDE1 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE Page Power Management Setup ACPI Suspend Type Soft-off by PWR_BTTN Parallel Port Mode ECP Mode Use DMA PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment PC Health Status Reset Case Open Status Current Voltage (V) VCORE / +3.3V / DDR 2.5V / +12V MB Intelligent Tweaker (M.I.T.) Configure DRAM Timing CAS Latency Setting DRAM RAS Active Time DRAM RAS Precharge Time AGP/PCI Clock Control - 35 - BIOS Setup Load Fail-Safe Defaults Set Supervisor/User Password Load Optimized Defaults Exit Without Saving Save & Exit Setup Revision History Chapter 3 Install Drivers INSTALL CHIPSET DRIVER Pictures below are shown in Windows XP Install Drivers Item Description Contact Us - 39 - Contact Us - 40 -8S661FXMP-RZ Motherboard