Intel 8S661FXMP-RZ - page 28

- 28 -8S661FXMP-RZ Motherboard

English

Onboard LAN device

Enabled Enable Onboard LAN function. (Default value)

Disabled Disable this function.

USB Controller

Enabled Enable USB Controller. (Default value)

Disabled Disable USB Controller.

USB Legacy Support

Enabled Enable USB Legacy Support.

Disabled Disable USB Legacy Support. (Default value)

SiS Serial ATA Controller

Enabled Enable SiS Serial ATA Controller.(Default value)

Disabled Disable SiS Serial ATA Controller.

SiS Serial ATA Mode

IDE Set SiS Serial ATA Mode to IDE.

RAID Set SiS Serial ATA Mode to RAID. (Default value)

Onboard Serial Port 1

Disabled Disable onboard Serial port 1.

3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)

2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3.

3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.

2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.

Auto BIOS will automatically setup the port 1 address.

Onboard Serial Port 2

Disabled Disable onboard Serial port 2

3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8/IRQ4.

2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)

3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8/IRQ4.

2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8/IRQ3.

Auto BIOS will automatically setup the port 2 address. .

Onboard Parallel port

Disabled Disable onboard LPT port.

378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value)

278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

Contents

Main 8S661FXMP-RZ User's Manual Intel Pentium 4 Processor Motherboard Rev. 1002 12ME-661FXMPRZ-1002 Page Preparing Your Computer Installing the motherboard to the chassis Table of Content Chapter 1 Introduction Features Summary Page Introduction- 7 - 8S661FXMP-RZ Motherboard Layout 8S661FXMP-RZ Block Diagram Hardware Installation Process Step 2 Step 1 Step 3 Step 1: Install the Central Processing Unit (CPU) Step 1-1: CPU Installation Step 1-2: CPU Cooling Fan Installation Step 2: Install memory modules Step 3: Install expansion cards Step 4: Install I/O Peripherals Cables Step 4-1: I/O Back Panel Introduction Step 4-2: Connectors Introduction 3) CPU_FAN (CPU FAN Connector) 1/2) ATX_12V/ATX (Power Connector) 4) SYS_FAN (System FAN Connector) 5) FDD (Floppy Connector) 6) IDE1/ IDE2 (IDE1/IDE2 Connector) - 16 - 8S661FXMP-RZ Motherboard 8) F_PANEL (2x10 pins connector) 7) SATA0/SATA1 (Serial ATA Connector, Controlled by SiS964) 9) BAT (Battery) CAUTION + 10)F_AUDIO (Front Audio Panel Connector) 11)CD_IN (CD In Connector) 12) SPDIF_IO (SPDIF In/Out) 13)SUR_CEN 14)F_ USB1 / F_USB2 (Front USB Connectors) 16)COMB (COMB Connector) 15)CI (Chassis Intrusion, Case Open) Page Chapter 2 BIOS Setup CONTROL KEYS ENTERING BIOS Setup Main Menu Status Page Setup Menu / Option Page Setup Menu Page Standard CMOS Features Date Time IDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Page Advanced BIOS Features Boot Up Floppy Seek Page Integrated Peripherals IDE1 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE Page Power Management Setup ACPI Suspend Type Soft-off by PWR_BTTN Parallel Port Mode ECP Mode Use DMA PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment PC Health Status Reset Case Open Status Current Voltage (V) VCORE / +3.3V / DDR 2.5V / +12V MB Intelligent Tweaker (M.I.T.) Configure DRAM Timing CAS Latency Setting DRAM RAS Active Time DRAM RAS Precharge Time AGP/PCI Clock Control - 35 - BIOS Setup Load Fail-Safe Defaults Set Supervisor/User Password Load Optimized Defaults Exit Without Saving Save & Exit Setup Revision History Chapter 3 Install Drivers INSTALL CHIPSET DRIVER Pictures below are shown in Windows XP Install Drivers Item Description Contact Us - 39 - Contact Us - 40 -8S661FXMP-RZ Motherboard