Manuals / Intel / Computer Equipment / Computer Hardware

Intel AX965Q Power Management Setup, ACPI Function, ACPI Suspend Type, Run VGABIOS if S3 Resume

Models: AX965Q

1 81

Download 81 pages 24.11 Kb

Page 71

Image 71

User’s Manual

2.2.5Power Management Setup

The power management setup controls the single board computer's “green” features to save power. The following screen shows the manufacturer’s defaults.

2.2.5.1 ACPI Function

The choices are “Enabled” and “Disabled”.

2.2.5.2 ACPI Suspend Type

This item allows you to set ACPI suspend type to S1/POS(Power On Suspend) or S3/STR(Suspend To RAM).

2.2.5.3 Run VGABIOS if S3 Resume

Select “Auto” to run VGA BIOS if S3 resume automatically. The “Yes” enables running VGA BIOS if S3 resume. The “No” disables this function.

ATX Main board 71

Page 71

Image 71

Intel AX965Q user manual Power Management Setup, ACPI Function, ACPI Suspend Type, Run VGABIOS if S3 Resume, User’s Manual

Contents

AX965Q User’s Manual Block Diagram ContentsSafety Information Specifications SummaryATX Main board User’s ManualContents BIOS SetupATX Main board Safety InformationElectrical safety Operation safetyATX Main board Technical SupportConventions Used in This Guide User’s ManualATX Main board Packing ListDate Revision HistoryRevision Revision HistorySystem Specifications Summary4 x COM, 10 x USB 2.0, 5 x SATA or 7 x SATA connectors for ICH8DO ATX Main boardDisplay Specifications SummaryUser’s Manual ATX Main boardATX Main board Block DiagramATX Main board Product1 introductionUser’s Manual it supportsATX Main board Production Introduction1.1 Before you Proceed Onboard LEDUser’s Manual 1.2.1 Placement Direction1.2 Motherboard Overview 1.2.2 Screw HolesATX Main board 1.3 Motherboard LayoutLabel 1.3.1 Layout Content ListRear Panel Connector SlotsOptional for ICH8DO Internal ConnectorReserved Manufacture use onlyATX Main board 1.4 Central Processing Unit CPUUser’s Manual ATX Main board 1.4.1 Installing the CPUATX Main board User’s Manual4. Lift the load plate with your thumb and forefinger to a 100º angle A, then push the PnP cap from the load plate window to remove B ATX Main board 1.4.2 Installing the CPU Heatsink and FanATX Main board 2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in placeUser’s Manual 2. Rotate each fastener counterclockwise 1.4.3 Uninstalling the CPU Heatsink and Fan1. Disconnect the CPU fan cable from the connector on the motherboard ATX Main boardATX Main board 5. Rotate each fastener clockwise to ensure correct orientation when reinstallingUser’s Manual Socket 1.5 System Memory1.5.1 DIMM Sockets Location Channel32-bit 1.5.2 Memory ConfigurationsNotes on memory limitations User’s ManualChip. No 1.5.2.1 Qualified Vendors Lists QVL － DDR2-800MHz CapabilitySize VenderVender 1.5.2.2 Qualified Vendors Lists QVL － DDR2-667MHz CapabilityUser’s Manual SizeChip. No ATX Main boardSize VenderVender 1.5.2.3 Qualified Vendors Lists QVL － DDR2-553MHz CapabilityUser’s Manual SizeATX Main board 1.5.3 Installing a DIMMATX Main board 1.5.4 Removing a DIMMUser’s Manual 2. Remove the DIMM from the socketATX Main board 1.6.1 Installing an Expansion Card1.6.2 Configuring an Expansion Card 1.6 Expansion SlotsUser’s Manual 1.6.3 Standard Interrupt AssignmentsPriority Standard FunctionATX Main board 1.6.4 PCI Slots1.6.5 PCI Express X16 Slot 1.6.6 PCI Express X4 SlotATX Main board 1.7 Jumpers1.7.1 Clear RTC RAM CLRTC User’s ManualATX Main board 1.7.2 Keyboard Power KBPWR+5V Default +5VSB ACT / LINK LED 1.8 Connectors1.8.1 Rear Panel Connectors Description6-channel HeadsetPort 2-channelDescription User’s ManualLabel FunctionATX Main board 1.8.2 Internal Connectors 1.8.2.1 Front Panel Audio Connector AAFPATX Main board 1.8.2.2 ATX Power Connector ATX12V, EATXPWRImportant notes on the Motherboard Power Requirements User’s ManualATX Main board 1.8.2.3 Optical Drive Audio Connector CDCHAFAN1 CHAFAN2 CPUFAN 1.8.2.4 CPU & Chassis Fan Connector CPUFAN, CHAFAN1, CHAFAN2User’s Manual ATX Main boardATX Main board 1.8.2.5 Power Fan Connector PWRFAN1.8.2.6 Serial Port Connector 1 COM1 1.8.2.7 Serial Port Connector 2 COM2User’s Manual 1.8.2.8 Serial Port Connector 3 COM31.8.2.9 Serial Port Connector 4 COM4 1.8.2.10 Floppy Disk Drive Connector FLOPPYz Reset Button 2-pin RESET 1.8.2.11 System Panel Connector FPANELz System Power LED 2-pin PWRLED z ATX Power Button/Soft-off Button 2-pin PWRSWSignal Description 1.8.2.12 IEEE 1394a Connector IE13942, Optional1.8.2.13 IrDA Connector IRCON1 z Signal Description SignalCable connector 1.8.2.14 Primary EIDE Connector PRIEIDEDrive jumper setting Mode of devicesATX Main board 1.8.2.16 Digital Audio Connector SPDIFOUTUser’s Manual ATX Main board 1.8.2.17 Serial ATA RAID Connector SATARAID1ATX Main board 1.8.2.18 USB 2.0 Connector USB56, 78User’s Manual ATX Main board 1.8.2.19 Trusted Platform Module TPM Connector TPMSLOT1User’s Manual BIOS setup2This chapter tells how to change of the BIOS parameters are also providedATX Main board BIOS Setup2.1 BIOS Setup Program 2.1.2 List Box 2.1.1 Legend BoxKeys Function DescriptionATX Main board 2.2 BIOS Menu Screen2.2.1.2 Time 2.2.1 Standard CMOS Featuresz IDE Device Setup 2.2.1.1 Date Day, xx/xx/xxxx2.2.1.7 Memory 2.2.1.4 Driver A/B2.2.1.5 Video 2.2.1.6 Halt OnATX Main board 2.2.2 Advanced BIOS FeaturesUser’s Manual ATX Main board 2.2.2.1 CPU FeaturesATX Main board 2.2.2.5 Quick Power On Self Test2.2.2.4 CPU L1 & L2 & L3 Cache User’s Manual2.2.2.8 Swap Floppy Drive 2.2.2.6 First / Second / Third Boot Device2.2.2.7 Boot Other Device 2.2.2.9 Boot Up Floppy Seek2.2.2.13 Typematic Rate Chars/Sec 2.2.2.10 Boot Up NumLock Status2.2.2.12 Typematic Rate Setting 2.2.2.11 Gate A20 Option2.2.2.19 Small Logo EPA Show 2.2.2.16 APIC Mode2.2.2.17 MPS Version Control for OS 2.2.2.18 OS Select for DRAM 64MBUser’s Manual 2.2.3 Advanced Chipset Features2.2.3.1 System BIOS Cacheable 2.2.3.2 Memory Hole at 15M-16M2.2.3.7 DVMT/FIXED Memory Size 2.2.3.6 DVMT Mode2.2.3.3 PCI Express Root Port Function 2.2.3.4 PEG/Onchip VGA Control 2.2.3.5 On-Chip Frame Buffer SizeATX Main board 2.2.4 Integrated Peripherals 2.2.4.1 OnChip IDE DeviceUser’s Manual ATX Main board 2.2.4.2 Super I/O DeviceATX Main board 2.2.4.3 Watch Dog Timer SelectUser’s Manual ATX Main board 2.2.4.4 USB Device Setting2.2.5.2 ACPI Suspend Type 2.2.5 Power Management Setup2.2.5.3 Run VGABIOS if S3 Resume 2.2.5.1 ACPI Function2.2.5.6 Video Off In Suspend 2.2.5.4 Power Management2.2.5.9 Suspend Mode 2.2.5.5 Video Off Method2.2.5.11 Soft-off by PWR-BTTN 2.2.5.10 HDD Power Down2.2.5.13 Power On by Ring 2.2.5.15 Resume by AlarmATX Main board 2.2.6 PnP/PCI Configurations 2.2.6.1 Init Display First2.2.6.2 Rest Configuration Data 2.2.6.3 Resource Controlled ByATX Main board 2.2.6.6 Maximum Payload SizeUser’s Manual 2.2.7.4 Spread Spectrum 2.2.7 Frequency/Voltage Control2.2.7.2 CPU Clock Ratio 2.2.7.3 Auto Detect PCI ClkATX Main board 2.2.8 Load Fail-Safe DefaultsUser’s Manual ATX Main board 2.2.9 Load Optimized DefaultsATX Main board 2.2.10 Set Supervisor/User PasswordPlease Confirm Your Password User’s ManualATX Main board 2.2.11 Save and Exit SetupATX Main board 2.2.12 Exit Without SavingUser’s Manual