Intel SHG2 Add-in Board Connectors , Video

Description 13

Add-in Board Connectors

The server board has the following add-in board connectors:

• Two 184-pin full-length, 3.3 V, PCI-X 64-bit/100 MHz connectors.

• Three 120-pin full-length, 5 V, standard PCI 32-bit/33 MHz connectors.

• One 184-pin full-length, 3.3 V, connector that is capable if PCI-X 64-bit/133 MHz operation.

To enable PCI-X 64-bit/133 MHz operation, you must disable the onboard SCSI controller

using BIOS Setup. See page 57 for more information on using BIOS Setup. The default

operation of this connector (slot 6) is PCI 64-bit/66 MHz operation.

Video

The system has an integrated ATI Rage XL 32-bit high-performance SVGA subsystem that

supports the following:

• BIOS compatibility with all standard VGA modes

• 8 MB of video memory

• Pixel resolutions up to 1600 x 1200 pixels per inch (ppi) in 8/16/24/32 bpp modes under 2D

and up to 1024 x 768 ppi in 8/16/24/32 bpp modes under 3D

• Both CRT and LCD monitors up to 100 Hz vertical refresh rate

Table 2. Video Modes

SHG2 2D Mode Video Support

2D Mode

Refresh Rate (Hz) 8 bpp 16 bpp 24 bpp 32 bpp

640x480 60, 72, 75, 90, 100 Supported Supported Supported Supported

800x600 60, 70, 75, 90, 100 Supported Supported Supported Supported

1024x768 60, 72, 75, 90, 100 Supported Supported Supported Supported

1280x1024 43, 60 Supported Supported Supported Supported

1280x1024 70, 72 Supported – Supported Supported

1600x1200 60, 66 Supported Supported Supported Supported

1600x1200 76, 85 Supported Supported Supported –

3D Mode Refresh Rate (Hz) SHG2 3D Mode Video Support with Z Buffer Enabled

640x480 60, 72, 75, 90, 100 Supported Supported Supported Supported

800x600 60, 70, 75, 90, 100 Supported Supported Supported Supported

1024x768 60, 72, 75, 90, 100 Supported Supported Supported Supported

1280x1024 43, 60, 70, 72 Supported Supported – –

1600x1200 60, 66, 76, 85 Supported – – –

3D Mode Refresh Rate (Hz) SHG2 3D Mode Video Support with Z Buffer Disabled

640x480 60, 72, 75, 90, 100 Supported Supported Supported Supported

800x600 60, 70, 75, 90, 100 Supported Supported Supported Supported

1024x768 60, 72, 75, 90, 100 Supported Supported Supported Supported

1280x1024 43, 60, 70, 72 Supported Supported Supported –

1600x1200 60, 66, 76, 85 Supported Supported – –

Contents

Main Page Contents 1 Description 2 Server Board Installation 3 Upgrading 4 Configuration Software and Utilities 5 Solving Problems 8 Regulatory and Integration Information 9 Equipment Log Worksheet Index Figures Tables Page 1 Description Server Board Features Table 1. Server Board Features Back Panel Connectors Figure 1. Back Panel Connectors Server Board Connector and Component Locations Processor Memory Add-in Board Connectors Video SCSI Controller Modular RAID Capable PCI-X Slot 6 IDE Controller USB Interface Network Controllers Network Teaming Features Adaptive Load Balancing Keyboard and Mouse ACPI Security Security with Mechanical Locks and Monitoring Software Locks Using Passwords Secure Mode Summary of Software Security Features Table 3. Software Security Features (continued) 2 Server Board Installation Tools and Supplies Needed Before You Begin Emissions Disclaimer Safety Cautions Safety and Regulatory Compliance Minimum Hardware Requirements Processor Memory Power Supply Installation Notes Installation Procedures Installing the I/O Gasket and Shield Attaching the Gasket to the I/O Shield Attaching the Label to the I/O Shield Page Installing Memory 1A 1B Configuring Chassis Standoffs Installing the Server Board Installing the Processor(s) Page Page Installing the Processor Wind Tunnel Page Page Making Connections to the Server Board Cable Routing Intel SC5200 Base Chassis Floppy and Front Panel Cables A B Cable Routing Intel SC5200 Hot-Swap, Redundant Power Chassis Installing the Serial B Cable Finishing Up Getting Started with Intel Server Management and Intel SMaRT Tool (Optional) Installing a Service Partition on the Server (Optional) Installing your Operating System Installing Intel Server Management Installing Intel SMaRT Tool 3 Upgrading Tools and Supplies Needed Cautions Memory 1A 1B Processors Adding or Replacing a Processor Page Page Installing the Processor Wind Tunnel Page Page Removing a Processor Replacing the Backup Battery WARNING ADVARSEL! ADVARSEL VARNING Page Page 4 Configuration Software and Utilities Table 4. Configuration Utilities Hot Keys Use the keyboards numeric pad to enter numbers and symbols. Power-On Self-Test (POST) Using BIOS Setup Record Your Setup Settings If You Cannot Access Setup Starting Setup Using the System Setup Utility Creating SSU Diskettes Running the SSU Working with the GUI Customizing the SSU Interface Exiting the SSU Setting Boot Device Priority Setting Passwords and Security Options Setting the Admin Password Setting the User Password Setting Security Options Viewing the System Event Log Viewing FRU Information Viewing Sensor Data Records Updating System Firmware and BIOS Updating the BIOS Updating the Firmware Verifying the Firmware Saving and Restoring the System Configuration Saving a Configuration Restoring a Configuration Alerting for Platform Events Setting Up Email Alerts Setting Up Paging Alerts Setting Up LAN Alerts Managing the Server Remotely Setting Up Remote LAN Access Setting Up Remote Modem or Serial Access FRUSDR Load Utility When to Run the FRUSDR Load Utility What You Need to Do How You Use the FRUSDR Load Utility Command Line Format Parsing the Command Line Displaying Usage Information Displaying a Given Area Using Specified CFG File Page Upgrading the BIOS Preparing for the Upgrade Recording the Current BIOS Settings Obtaining the Upgrade Utility Creating a Bootable Diskette Upgrading the BIOS Recovering the BIOS Changing the BIOS Language Using the Firmware Update Utility Making a BMC Firmware Update Diskette Making the Update Diskette Bootable Updating the BMC Firmware Recovering the BMC Firmware Updating the FRU/SDR Files Making a FRU/SDR File Update Diskette Making the Update Diskette Bootable Updating the FRU/SDR Files Using the Adaptec SCSI Utility Running the SCSI Utility 5 Solving Problems Resetting the System Initial System Startup Running New Application Software After the System Has Been Running Correctly More Problem Solving Procedures Preparing the System for Diagnostic Testing Monitoring POST Verifying Proper Operation of Key System Lights Specific Problems and Corrective Actions Power Light Does Not Light No Characters Appear on Screen Characters Are Distorted or Incorrect System Cooling Fans Do Not Rotate Properly Diskette Drive Activity Light Does Not Light Hard Disk Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not Light Cannot Connect to a Server Problems with Network PCI Installation Tips Problems with Application Software Bootable CD-ROM Is Not Detected 6 Getting Help World Wide Web http://support.intel.com/support/motherboards/server/SHG2 Telephone Page 7 Technical Reference Server Board Jumpers Figure 37. Jumper Locations Table 7. Configuration Jumper (CN43) Enabling PCI-X on Slot 6 and Disabling On-board SCSI 8 Regulatory and Integration Information Product Regulatory Compliance Product Safety Compliance Product EMC Compliance Product Regulatory Compliance Markings This product is marked with the following Product Certification Markings: Electromagnetic Compatibility Notices FCC (USA) INDUSTRY CANADA (ICES-003) Europe (CE Declaration of Conformity) Taiwan Declaration of Conformity Korean RRL Compliance Australia / New Zealand 9 Equipment Log Worksheet Equipment Log Equipment Log (continued) Index A B C D F G-J K-L M-N P R S T-U V-W