CHAPTER 2
These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to your hard disk documentation for the jumper setting.
Pin | Description | Pin | Description | Pin | Description |
|
|
|
|
|
|
1 | Reset # | 2 | GND | 3 | Data 7 |
4 | Data 8 | 5 | Data 6 | 6 | Data 9 |
7 | Data 5 | 8 | Data 10 | 9 | Data 4 |
10 | Data 11 | 11 | Data 3 | 12 | Data 12 |
13 | Data 2 | 14 | Data 13 | 15 | Data 1 |
16 | Data 14 | 17 | Data 0 | 18 | Data 15 |
19 | GND | 20 | No connector | 21 | No connector |
22 | GND | 23 | IOW # | 24 | GND |
25 | IOR # | 26 | GND | 27 | IOCHRDY |
28 | No connector | 29 | No connector | 30 | |
31 | Interrupt | 32 | No connector | 33 | SA1 |
34 | No connector | 35 | SA0 | 36 | SA2 |
37 | HDC CS0 # | 38 | HDC CSI # | 39 | HDD Active # |
40 | GND |
|
|
|
|
2.5.6 Floppy Disk Connector: FLOPPY
CHAPTER 2
2.88 MB,
This connector supports the provided floppy drive ribbon cable. After connecting the single and to the board, connect the two plugs on the other end to the floppy drives.
Pin | Description | Pin | Description | Pin | Description |
|
|
|
|
|
|
1 | GND | 2 | Reduce write current | 3 | GND |
4 | No connector | 5 | GND | 6 | No connector |
7 | GND | 8 | Index# | 9 | GND |
10 | Motor enable A# | 11 | GND | 12 | Drive select B# |
13 | GND | 14 | Drive select A# | 15 | GND |
16 | Motor enable B# | 17 | GND | 18 | Direction# |
19 | GND | 20 | STEP# | 21 | GND |
22 | Write data# | 23 | GND | 24 | Write gate# |
25 | GND | 26 | Track 0 # | 27 | GND |
28 | Write protect# | 29 | GND | 30 | Read data# |
31 | GND | 32 | Side 1 select# | 33 | GND |
34 | Disk change# |
|
|
|
|
2.5.7 Adapter connector for 10/100 LAN: LAN1
This connector is for the LAN adapter that has LED indicate the 10/100Mbps transfer rate / Link / Act status of Ethernet capability of the CPU card. The follow table shows the pin assignments of this connector.
The floppy interface can be configured for the following floppy drive capacities and sizes:
360KB,
1.2 MB,
720KB,
1.2 MB,
C N 1 3
1 2 3 4 5 6 7 8
L in k | T r a n s m it |
L E D | L E D |
PIN No. | Function | PIN No. | Function |
|
|
|
|
1 | TX+ | 5 | GND |
|
|
|
|
2 | TX- | 6 | NC |
|
|
|
|
3 | NC | 7 | RX+ |
|
|
|
|
4 | GND | 8 | RX- |
|
|
|
|
SYS7180VE User’s Manual | 17 |
18 | SYS7180VE User’s Manual |