OPERATING INSTRUCTIONS
Operation
Note: These instructions pertain to all bath products manufac- tured by Jacuzzi Whirlpool Bath. Not all features discussed in this instruction pamphlet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath© are designed for "fill and drain," which means the bath should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools or spas.
LED DISPLAY
101
ON/OFF | LIGHT COLOR CYCLE |
PUMP MOTOR | BATH LIGHT ON/OFF |
|
Control Panel
Comfort Plus With Light System
The Comfort Plus With Light System control panel, located on the bath, allows you to control the pump, observe the water temperature, and control the Chromotherapy lighting system while in the bath. During operation the system displays water temperature allowing for an approximate temperature fill. The Chromotherapy lighting system controls the 2 Channel Chromotherapy lamps where you can turn on bath lighting in white, a color of choice, or a continuous flow through all colors. The system (pump, heater, and display) automatically shuts off after 30 minutes of operation, the Chromotherapy lighting system has a 4 hour lamp timeout. To restart the system (pump, heater, and display) simply press the ON/OFF button again.
CAUTION: Temperature sensors and values are approximate and may vary. Use caution when entering heated water.
On/Off Pump/Motor
Pressing this button will turn ON the pump/motor. Pressing a sec- ond time will turn OFF the pump/motor.
Bath Light ON/OFF
Pressing this button will turn ON the bath light(s). The light(s) will come ON displaying the White colored light. Pressing a second time will turn all light(s) OFF. (Use the "Light Color Cycle" button to turn ON the color lights.)
Light Color Cycle
Pressing this button will turn ON the colored light(s) to the "favorite" light (default is blue). Pressing this button again will begin the light(s) cycling through each of the available colors. This will continue until the Light Color Cycle button is pushed again, which stops the light cycling action on the current color. Press the button again and you will begin the Light Color Cycle again.
To create a new “favorite” color: Allow the lights to rotate to the new "favorite" light color. Stop the cycling on that color. Press and hold down the button for three seconds (the light will then blink to confirm the new "favorite").
LED Display
The Comfort Plus control panel water temperature displays when the water level covers the internal water sensor even if the Comfort Plus With Light System controls are not turned ON. This feature is designed to give a temperature indication even if the whirlpool system is not being used.
Pressing and holding the ON/OFF button for three (3) seconds displays a "time remaining" minute countdown. After displaying the "time remaining" countdown for 30 seconds, the readout reverts back to the temperature display.
LED DISPLAY
101
ON/OFF
PUMP MOTOR
Control Panel
Comfort Plus No Light System
The Comfort Plus control panel, located on the bath, allows you to control the pump and observe the water temperature while in the bath. During operation the system displays water temperature allowing for an approximate temperature fill. The system (pump, heater, and display) automatically shuts off after 30 minutes of operation. To restart simply press the ON/OFF button again.
CAUTION: Temperature sensors and values are approximate and may vary. Use caution when entering heated water.
On/Off Pump/Motor
Pressing this button will turn ON the pump/motor. Pressing a sec- ond time will turn OFF the pump/motor.
LED Display
The Comfort Plus control panel water temperature displays when the water level covers the internal water sensor even if the Comfort Plus No Light System controls are not turned ON. This feature is designed to give a temperature indication even if the whirlpool system is not being used.
Pressing and holding the ON/OFF button for three (3) seconds displays a "time remaining" minute countdown. After displaying the "time remaining" countdown for 30 seconds, the readout reverts back to the temperature display.
Water Level
Close the drain and fill the bath until water is at least 1" above the highest jet (see water line indicated in the illustration). Do not turn on the whirlpool system at any time if the jets are not completely immersed in water. Running the whirlpool system when there is insufficient water in the bath could result in water spraying outside the bath area. Running the whirlpool system without water will dam- age the recirculating pump.
Do not immerse the control panel by overfilling the bath.
FILL TO AT LEAST
1" ABOVE HIGHEST JET
ENGLISH
9
Jacuzzi Whirlpool Bath© BP43000 2/05
