LEVEL ADJUSTMENT

The Finestra comes factory pre-leveled however the floor may require a need to make adjustment. The leveling legs operate in a manner as those in a washer-dryer.

NOTE: It is important check the level prior to water testing. The unit must be level for water testing as this helps with the door seal alignment.

If it is necessary to level the bath, start by leveling the outside four legs, then move to the two legs on the door. The unit is preleveled prior to shipment and should not be

Nut (Top)

Rail

Nut (Bottom)

Threaded

Levelintg

Leg

tampered with if not required.

CAUTION: Under no circumstances will it be necessary to remove the levelling feet.

Foot

Leveling Legs

(Floor)

ELECTRICAL CONNECTIONS

All circuits must be protected by a dedicated Ground Fault Circuit Interrupter (GFCI). Refer to the electrical specification for each model on pages 5-11. Install duplex outlets to the studwall underneath the bathtub, at least 4 inches (102 mm) above the floor or in accordance with local building or electrical codes. Duplex outlets are not provided. Because these units are manufactured with an electronic control panel, no remote switch or timer is necessary.

With a #8 solid copper wire, bond the heater to the house electrical panel or approved local bond. A bonding lug is provided on the heater. With another #8 solid copper wire, bond the pump/motor to the house electrical panel or approved local bond. A bonding lug is provided on the pump/motor.

At initial start-up and before each use thereafter with power ON, push the dedicated GFCI test button on each circuit. The reset button should pop out. Push this button in to reset. If the interrupter fails to operate in this manner, there is a ground current flowing or a device malfunction, indicating the possibility of electrical shock. Turn off power and do not use the bath until the source of the problem has been identified and corrected.

Danger: Risk of electric shock. Connect only to a circuit protected by a dedicated Ground Fault Circuit Interrupter (GFCI).

Caution: Operating the motor/pump without enough water in the bath can cause leaking and permanent damage to the pump. Before power is applied to the installation, make sure the switch is in the OFF position to avoid pump damage.

It is necessary to install separate dedicated GFCI protected circuits for both duplex receptacles (not provided).

ELECTRICAL CONNECTION

1.

The motor is connector the the Control Box.

 

2.

The Control Box is connected to the Ozone unit.

 

3.

The Ozone unit is connected to the power receptacle.

 

Ozone unit

NOTE: The heater is conected independently.

Blower

Motor

 

Blower

Power connector

Motor

 

 

 

 

 

Rapid heater

 

Control box

 

 

 

 

 

Right side of unit

 

Left side of unit

Jacuzzi Whirlpool Bath: Finestra Walk-in Bath

Page 13

FL61000B • 10/07

Page 12 Page 14
Page 13
Image 13
Jacuzzi FL61000 manual Leveling Legs, Right side of unit Left side of unit
Page 12 Page 14

FL61000 specifications

The Jacuzzi FL61000 is an innovative and versatile hot tub that combines luxury with advanced technology to create an enjoyable and therapeutic experience. Designed for both relaxation and socialization, the FL61000 can accommodate up to six individuals, making it perfect for family gatherings or intimate get-togethers with friends.

One of the standout features of the Jacuzzi FL61000 is its powerful hydrotherapy system. The hot tub is equipped with strategically placed jets that provide targeted massage to various muscle groups throughout the body. With a variety of jet types, including rotating and directional jets, users can customize their massage experience according to individual needs.

The FL61000 also boasts an advanced water management system, which enhances the quality and clarity of water. Equipped with a filtration system that uses enhanced sanitation technologies, including ozone purification, the hot tub minimizes chemical usage while ensuring clean and safe water. This gives users peace of mind while they indulge in relaxation.

In terms of design, the Jacuzzi FL61000 is aesthetically pleasing with its sleek, modern lines and available in several stylish colors that can complement any outdoor space. Its durable acrylic shell provides long-lasting beauty and is engineered to withstand various weather conditions. The hot tub is framed with a robust composite base, ensuring longevity and stability.

Energy efficiency is another hallmark of the FL61000. It features an insulating cover that reduces heat loss, ensuring that energy costs are kept low. The hot tub is also equipped with an energy-efficient pump that minimizes electricity consumption without compromising performance.

Additional technologies integrated into the Jacuzzi FL61000 enhance user convenience and enjoyment. The intuitive control panel allows for easy customization of temperature, jet speed, and lighting. Some models even support smart technology, offering remote access through mobile devices for added flexibility.

Finally, safety features such as non-slip surfaces and easy-access steps ensure that users can enjoy the hot tub with peace of mind. Whether seeking relief from everyday stress or looking to create a social hub at home, the Jacuzzi FL61000 delivers a luxurious experience that can be enjoyed year-round.
Top Page Image Contents