OPERATION
NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features discussed in this instruction pamphlet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for “fill and drain,” which means the bath should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas available.
Once the bath is installed, remove any residue or foreign materials left over from construction.
NOTE: Use these chemicals only on SURFACE stains. Other dirt can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or plastic edge; do not use metal scrapers, wire brushes or other metal tools, as they will damage the bath’s surface.
Water Level
Close the drain and fill the bath until water is at least 1” to 2” (2.5 to 5.08 cm) above the highest jet (see water line indicated in the illustration). Do not turn on the whirlpool system at any time if the jets are not completely immersed in water. Do not immerse the control panel by overfilling the bath. Running the whirlpool system when there is insufficient water in the bath could result in water spraying outside the bath area. Running the whirlpool system without water will damage the recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop below the jets which could result in water being sprayed out of the unit. To prevent this, you must turn unit off before exiting bath.
Controlling Whirlpool Action
The whirlpool action in your bath, controlled manually and electronically, is influenced by three factors – direction of flow, force of water, and force of air. Every bath manufactured by Jacuzzi Whirlpool Bath that is equipped with fully adjustable PowerPro® jets, are manually adjustable for direction and water force. Some baths have additional jets which can be adjusted for direction only. Baths equipped with 2 speed motors and electronic controls can also influence water force and force of air.
Direction: To change the direction of the water flow, swivel the jet nozzle to the desired angle. The jets can be directed individually toward any location on your body to provide a hydromassage. The jets can also be adjusted so that they all point in the same direction (clockwise or counterclockwise) to circulate the water in a circular motion around the bath, causing a total whirlpool effect.
Water Force: The high volume, fully adjustable PowerPro® jets can be manually adjusted to control the force of the water coming into the bath. For robust action, increase the force of the flow by rotating the jet handles to the left (counterclockwise). For a more gentle effect, rotate
the handles to the right (clockwise). Customize water force by lowering water volume of one (1) jet(s) to increase water force in another jet(s). In units with 2 speed motors the water force can be increased or decreased using the electronic control.
Never run the whirlpool system with all the jets closed.
FILL TO AT LEAST
1" - 2" ABOVE HIGHEST JET
Force of Air: For units with electronic controls the Force of Air is controlled electronically. Refer to the Electronic Control Panel instructions for details in adjusting Force of Air. Units with manual controls are discussed on page 22.
JETS
DIRECTIONALLYFULLY
ADJUSTABLEADJUSTABLE
CONTROL PANEL OPERATION
All tubs in this product line come with electronic controls and standard Chromotherapy. Read and follow the operation instructions for the control system of your unit.
General Functions
This Jacuzzi tub is equipped with an electronic control panel. The seven button panel controls a two speed pump/motor, Chromotherapy lighting, air controls, wave control, and in some units the blower. LED lights (in the control panel) indicate function levels. When switching between functions, the LED for the inactive functions will dim and the active function will brighten.
The bath is equipped with a water level sensor(s). When the water level is below the sensor, the pump/motor can not be activated. If the ON/OFF pump/motor button is pressed at this time, the pump/motor will not operate. When the water goes above the water level sensor, the pump/motor can be activated. If the water level drops below the level sensor, the pump/motor will shut OFF. To restart the pump/motor after the water level goes above the level sensor, the ON/OFF pump/motor button must be pressed. The pump/motor will automatically shut off 30 minutes after the pump/motor was turned on.
NOTE: Ensure the water level sensor located inside the bath is free of any soap or dirt buildup.
