SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly, heater, plumbing, and fittings necessary for whirlpool operation. A rotary drain/overflow kit is provided for installation on the bath, and an optional remote drain/ overflow assembly is also available.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only or the aluminum handles provided at the ends of the unit.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath’s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping.
NOTE: Prior to installation, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.
SPECIFICATIONS LH=Left Hand, RH=Right Hand
|
|
|
| L |
| |||
|
|
|
|
| ||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
2"
W
Service
Access
Service Access
H
14"
| BACK | LEFT END |
|
|
| FRONT |
| RIGHT END |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Drain/Overflow |
|
| Total Weight/Floor | Operating |
| Product | Skirt/ |
| |||
Model | Dimensions | Dimensions | Cutout | Loading | Gallonage |
| Weight | Mounting | Heater | ||||||
Finestra™ 6030 | 60” (1524 mm) L | 15” (381 mm) A | See |
| 1038 lb (472 kg), | 55 gal (208 liter) min, |
| See pages | Integral | Factory | |||||
LH, RH | 30” (762 mm) W | below | 41.5 lb/ft2 (202 kg/m2) | 75 gal (284 liter) max |
| 6 to 11 |
| installed | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Finestra™ 6036 | 60” (1524 mm) L | 18” (457 mm) A | See |
| 1177 lb (535 kg), | 55 gal (208 liter) min, |
| See pages | Integral | Factory | |||||
LH, RH | 36” (914 mm) W | below | 47.1 lb/ft2 (229 kg/m2) | 85 gal (321 liter) max |
| 6 to 11 |
| installed | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A
B
DRAIN/OVERFLOW
* Add 1/4" to this dimension when
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit (See page 7 to 12).
NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
2.All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3.Service access dimensions given are minimum size.
4.The overall dimensions are nominal with a tolerance of +0 and
Jacuzzi Whirlpool Bath: Finestra | Page | FL61000B • 10/07 |