15. ConnectElectrical (Four ConductorWire) (Figure 15) |
|
|
| |||
• | Remove the range electrical service cover, located on the back, lower |
| _ ;'_ | |||
|
|
|
|
|
| |
• | c oamp.esuholea.re shownwer |
| ||||
Removethe grounstrapscrewand bendthe strapup as | .Installa 3/4" |
|
| |||
| (1.91cm) cable cl | in the | provided,below the terminal block. | I, NOl |
| |
• | Strip 3" (7.62cm) | outer insulationfrom the cable. |
|
| , GROUND | |
• | Strip 1/2" (1,27cm)ofof insulationfrom each wire. |
|
| WIRE | ||
• | Pull the cablethroughthe cableclamp. |
|
| "BASe | ||
• | Make a loopin the bare groundwire and attachitto the rangewith the screw |
| ||||
• | that heldthe ground strap, |
|
|
| _. _'OROUNC)wlSE | |
Attach the BLACK, RED,and WHITE wires (see #14.) Tightenthe terminal |
|
| ||||
| block nuts and the cable clamp. |
|
|
| (Figure 15) |
• Tapethe ground strap to theWHITE wire as shown. Install electricalcover. 16. Install Options (Figure 16)
• If the backsplash or side panels are to be used, install according to
| instructionsincluded in those accessories. |
|
|
17. Position Range (Figure 17) |
|
| |
• |
|
| |
| approximately the same. Slide the range into place, taking care not to |
| |
| damagefloor covering. | . J' |
|
• | " 1" / | I | |
| range into place. Adjustfeet so range is adjacentto countertop surface. | 4 |
18, | (Figure 16) | |
NOTE: A risk of range tip over exists if the appliance is not installed in |
| |
accordancewith the installationinstructions provided.The proper use of these |
| |
devicesminimizesthe risk of |
| |
must still observesafety precautionsas statedin the USE and CARE MANUAL |
| |
and avoid usingthe oven door and/or lowerdrawer as a step stool. |
| |
Instructionsare providedfor installationin eithera wood or concretefloor.Any |
| |
othertype ofconstructionmayrequirespecialinstallationtechniquesas deemed |
| |
necessaryto provideadequatefastening of the |
| |
STEP 1 - LocatingThe Brackets |
| |
• | Placethe unitin itsfinal location. |
|
• | Removethe storagedrawer or lowerdoor panel (dependingon model |
|
| beinginstalled.) | (Figure 17) |
•Markthe floor at the right and leftwherethe rangefront meetsthe floor. NOTE: Protectthe floor with maskingtape prior to marking.
•Removethe range for access to the bracket mountingpositions. Use care to avoid damageto floor.
•Drawa lineon thefloor at the backof thecutoutwhich isoffset
•Locate the center (side to side) of the cutout. See illustration for
•Positionbrackets
_1 ,5,1
_1 | = | 2 5/16TYP |
| [59.21 cm] |
• | Use the bracketto mark holes for drilling. Proceedto STEP 2. | _ _'F.o._0RAL'wNES.AN_EAT | ||||
STEP2 - InstallingThe Brackets |
|
|
|
| I | |
| markedholepositions(a nailorawlmaybeusedif a drilJisnotavailable.) |
| I | (_8"2_'=.> | ||
|
| |||||
• | Wood Construction:Drill a I/8" pilot hole in the center of each of the |
| 2g | 7/8 |
| |
| _01/_" [5 _/_6" | |||||
| Secure the |
| 1(75.8s) (379s_/_S.1m)II | |||
| STEP3. |
|
|
|
|
|
• | Cement or Concrete Construction: Suitable screws for concrete | (Figure 18) |
| |||
| constructioncan beobtainedat a hardwarestore.Drillthe requiredsize |
| ||||
| hole for the screw obtained in the center of each of the marked hole |
| ||||
| positions.Secure the | _ |
|
|
| .._OKEr |
STEP3- Range Installation | __/_. |
| - | - |
| |
• | Alignthe range to its designatedlocationand slideit back into position. |
|
|
|
|
|
| Make surethat the rearlevelingfeet arefully insertedinto and secured | ___._" |
|
| ||
| by the |
|
|
|
|
|
|
|
|
|
|
|
5