Electrical Requirements

IMPORTANT: Observe all governing codes and ordinances. Save Installation Instructions for electrical inspector’s use.

It is the customer’s responsibility to contact a qualified electrical installer, and to ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■This fan is suitable for use with solid state speed controls.

■A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is required.

■Check with a qualified electrician if you are not sure the downdraft vent is properly grounded.

■The downdraft vent must be connected with copper wire only.

■The downdraft vent should be connected directly to the circuit breaker (or fused disconnect) box through flexible armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the downdraft vent can be moved if servicing is ever necessary.

■Wire sizes (copper wire only) and connections must conform with the rating of the appliance as specified on the model/ serial rating plate located on the front of the downdraft vent above the wiring box cover.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

■Two UL listed or CSA approved ½" (12.7 mm) conduit connectors.

■A wiring diagram is located on the downdraft vent base above the power control board cover.

Venting Requirements

IMPORTANT: Make sure there is proper clearance within the wall or floor before making exhaust vent cutouts.

■Use heavy (rigid) metal vent.

■Venting system must terminate to the outside.

■Do not terminate the vent system in an attic or other enclosed area.

■Do not use 4" (10.2 cm) laundry-type wall caps.

■Do not install 2 elbows together.

■Do not use plastic or metal foil vent.

■The length of vent system and number of elbows should be kept to a minimum to provide efficient performance.

■Use no more than three 90° elbows

■Make sure there is a minimum of 24" (61 cm) of straight vent between the elbows if more than one elbow is used.

■Use clamps to seal all joints in the vent system.

■Use caulking tape to seal the exterior wall or floor opening around cap.

■Do not cut joist or stud. If vent cutout falls over a joist or stud, a supporting frame must be constructed.

Flexible metal vent is not recommended. If it is used, calculate each foot of flexible vent as 2 ft (0.6 m) of rigid metal vent.

Flexible elbows count twice as much as standard elbows.

Recommended vent system length:

For either interior-mounted or exterior-mounted blower installations, the vent system length should not exceed the maximum lengths listed in the Maximum Length of Vent System chart. See “Calculating Vent System Length” in the “Venting Methods - Interior Mounted Vent Motor Only” section.

6

Page 5 Page 7
Page 6
Image 6
Jenn-Air W10201609B installation instructions Electrical Requirements, Venting Requirements, Recommended vent system length
Page 5 Page 7

W10201609B specifications

The Jenn-Air W10201609B is a premium refrigerator water filter designed to enhance water and ice quality in residential kitchens. This filtration system stands out due to its advanced technology and user-friendly design, ensuring that homeowners receive clean, great-tasting water straight from their refrigerator dispenser.

One of the primary features of the W10201609B is its ability to reduce a wide array of contaminants commonly found in tap water. It efficiently removes impurities such as chlorine, lead, mercury, and sediments, which can not only affect taste but also pose health risks. By filtering out these harmful substances, it provides families with peace of mind knowing that the water they consume is safe.

The filter is designed with an easy installation process, making it accessible for anyone without the need for professional help. Users can seamlessly replace their existing filter within minutes, ensuring minimal downtime and hassle. Additionally, the filter is compatible with specific Jenn-Air refrigerator models, serving as a perfect fit for those who prioritize brand integrity and performance.

The W10201609B boasts a standard lifespan of up to six months, providing approximately 200 gallons of filtered water, depending on usage. This longevity makes it a cost-effective solution for households, as it reduces the frequency of filter replacements. Moreover, the filter uses a carbon block technology that significantly improves the taste and odor of water, providing a refreshing experience every time.

Furthermore, Jenn-Air’s commitment to innovation is evident in the filter's construction, which features a robust design that enhances durability and reliability. This ensures consistent performance, even in high-demand situations. The W10201609B is also NSF certified, which guarantees that it meets strict standards for public health and safety.

In summary, the Jenn-Air W10201609B water filter is an essential component for homeowners who prioritize quality in their drinking water. With its advanced filtration capabilities, easy installation, and impressive lifespan, it stands as a testament to Jenn-Air's dedication to providing cutting-edge kitchen solutions. Utilizing this filter not only upgrades the water quality in the home but also enhances the overall culinary experience, making it a worthy addition to any modern kitchen.
Top Page Image Contents