Standard Installation - Flush Grille - Open or Closed Soffit
|
|
|
|
|
|
|
|
|
| D |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1" (2.54 cm) |
| Top Grille Filler |
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| E |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| 5³⁄₄" |
|
|
|
| Top Grille Panel |
|
|
| ||||
| (14.55 cm) |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
| 36 |
| 42 |
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Reveal |
| ³⁄₈" |
| ¹⁄₈" |
| ³⁄₈" |
| ¹⁄₈" | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D |
| 35¹⁄₄" |
| 35³⁄₄" | 41¹⁄₄" | 41³⁄₄" | ||||||||
|
| (89.54 cm) |
| (90.81 cm) | (104.76 cm) | (106.05 cm) | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
E |
| 35¹⁄₄ |
| 35³⁄₄" | 41¹⁄₄" | 41³⁄₄" | ||||||||
|
| (89.54 cm) |
| (90.81 cm) | (104.76 cm) | (106.05 cm) | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IMPORTANT: The grille panel height, shown in the Standard Installation Flush Grille graphic, allows for an air gap critical to refrigerator performance.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
Move the Refrigerator into House
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not completely installed.
Keep doors taped closed until refrigerator is completely installed.
Use two or more people to move and install refrigerator.
Failure to do so can result in death or serious injury.
1.Place an appliance dolly under the left side of the refrigerator as shown. Place the corner posts from the packing materials over the trims as appropriate. Slowly tighten the strap.
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not completely installed.
Keep doors taped closed until refrigerator is completely installed.
Use two or more people to move and install refrigerator.
Failure to do so can result in death or serious injury.
IMPORTANT:
■Do not remove the film covering until the refrigerator is in its operating location.
■All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.
■Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating location.
1.Remove and save the literature package and hardware kit located inside the refrigerator. Remove and save the literature, grille, and trim taped to the outside of the refrigerator.
NOTE: Do not remove tape and door bracing until the refrigerator is in its final location.
2.Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the
3.Place top of cardboard carton or plywood under refrigerator.
4.Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the
Install Anti-Tip Boards
IMPORTANT:
■If a solid soffit is not available, an
■It is recommended that board(s) be installed before the refrigerator is installed.
■Board(s) must be long enough to fully cover the width of the compressor cover.
■Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.
■During installation, raise the refrigerator up until the top of the refrigerator is making contact with the bottom of the
17
