Flame Appearance / Air Shutter Adjustment

The GF 300 BV gas stove is shipped from the factory equipped to burn Natural gas. If the stove has been converted for use with propane, the Air Shutter may require adjustment to achieve the desired flame appear- ance. Other installation related variables can also affect the flame picture. The Air Shutter may be opened or closed to provide the best flame picture for your specific installation.

Too large an air opening - the appliance will generate a flame that is blue and transparent, or an “anemic” flame.

Too small an air setting - the appliance will generate very long yellow flames resulting in soot. Sooting pro- duces black deposits on the logs, on the inside walls of the appliance, and potentially on the exterior termination cap. Sooting is caused by incomplete combustion in the flames and lack of combustion air entering the air shutter opening.

To adjust the air shutter:

1.Reach under the right side of the stove and loosen the wingnut located closest to you. See fig. 25. Slide the wingnut stud forward to open the air shutter and back to provide less air. Make adjustments in small incre- ments.

2.Tighten the wingnut to secure the shutter at the desired setting.

3.Allow the stove to burn for 30 minutes on the HIGH setting, observing the flame continuously. If the flame appears weak, slow, or sooty, repeat the process described above until the flame is as desired.

WARNING: AIR SHUTTER ADJUSTMENTS SHOULD ONLY BE PERFORMED BY A QUALIFIED PROFESSIONAL SERVICE TECHNICIAN.

Open Close

Figure 25. Loosen the wingnut to adjust the air shutter.

Optional Wall Thermostat or Remote Control

Use only a 750 millivolt DC two-wire circuit thermostat with this appliance. The thermostat should be placed in the same room as the heater, typically 5 feet off the floor. Avoid drafty areas or any area that may affect the accuracy of the thermostat.

The thermostat should be connected to the GF 300 BV using a minimum of 16 gauge wire with a maximum length of 25 feet of wire.

Connect the two thermostat wire leads to the two lower terminals on the terminal block located directly above the ignitor button. Do not overtighten the connections. IT IS NOT NECESSARY TO DISCONNECT ANY OTHER WIRES. See Fig. 26.

For thermostatic operation, the On/Off/T-Stat switch on the back of the stove must be in the T-stat position, and the pilot light must be running, as it is the power source for the thermostat.

At the thermostat, the two wires should be con- nected to the two connection screws on the thermostat base plate per the manufacturer’s instructions.

Remote Control

When using a remote, the remote receiver should be wired to the terminal block the same way the thermo- stat would be. See the instructions above.

Follow the operating instructions included with the Remote Control unit.

CAUTION:

LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING THE CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER OR DANGEROUS OPERATION. ALWAYS VERIFY PROPER OPERA- TION AFTER SERVICING THE APPLIANCE.

THERMOPILE

SPILL SWITCH

Black	Black
Red			ROCKER
White			SWITCH
			ON
TH	Purple		OFF
TH			OFF
TP			TSTAT
TH
TP
VALVE		Orange
VALVE			OPTIONAL
White			OPTIONAL
White			THERMOSTAT
		Yellow	THERMOSTAT
		Yellow	or
			or
			REMOTE
			CONTROL

TERMINAL

BLOCK

Figure 26. Valve and Accessory wiring diagram.

GF300 BV specifications

The Jotul GF300 BV is a contemporary gas stove that epitomizes elegance and efficiency. Known for its robust construction and exceptional performance, it serves as both a reliable heating source and a stunning centerpiece in any living space. This model is particularly popular among homeowners looking to blend functionality with aesthetic appeal.

One of the standout features of the Jotul GF300 BV is its advanced heating technology. Equipped with a powerful burner system, it delivers efficient heat while maintaining low emissions. The stove has a maximum output of 30,000 BTUs, making it suitable for a variety of room sizes. This capacity not only ensures ample warmth but also contributes to a consistent and pleasant environment during colder months.

The design of the GF300 BV is particularly noteworthy, featuring a large glass front that allows for an unobstructed view of the mesmerizing flames. This design choice enhances the ambiance of any room, transforming a simple heating appliance into a focal point. The stove also includes an adjustable flame height feature, allowing users to customize the intensity of the fire according to their preference.

In terms of efficiency, the Jotul GF300 BV is a leader in its class. It boasts an impressive efficiency rating, which translates to lower energy costs for homeowners. Additionally, the unit is designed to work seamlessly with modern home ventilation systems, ensuring optimal performance without compromising air quality.

Another significant characteristic of the Jotul GF300 BV is its versatility. It is available in a variety of finishes and styles, allowing it to complement diverse interior designs—from rustic to modern. The stove can be installed in several configurations, including as a freestanding model or as part of a zero-clearance fireplace.

Installation is straightforward, thanks to the back venting capability, which is particularly beneficial for homes with limited installation space. The unit is also equipped with a thermostat control system for improved user convenience.

Overall, the Jotul GF300 BV combines innovative technology with timeless design, making it a top choice for anyone looking to add warmth and style to their home. Its blend of efficiency, aesthetic appeal, and adaptability ensures it remains a popular choice in the world of gas heating solutions. Whether used in a cozy den or a grand living room, this gas stove will undoubtedly enhance the overall comfort and atmosphere of any space.

Jotul GF300 BV manual Flame Appearance / Air Shutter Adjustment, Remote Control

Models: GF300 BV