Manuals / JVC / Home Audio / Stereo System

JVC CA-UXB70, SP-UXB70 manual Connecting Speakers, 2Hold the clamp of the speaker terminal

Models: SP-UXB70 CA-UXB70

1 36

Download 36 pages 22.3 Kb

Page 10

Connecting Speakers

AM (MW) antenna

1

ANTENNA

Vinyl-covered wire

(not supplied)

2

AM (MW) loop antenna

(supplied)

1Connect the AM (MW) loop antenna to the AM LOOP terminals as illustrated.

2Turn the AM (MW) loop antenna until you have the best reception.

To connect an outdoor AM (MW) antenna

When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM (MW) loop antenna must remain connected.

For better reception of both FM and AM (MW)

•Make sure the antenna conductors do not touch any other terminals or connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

Connecting Speakers

To connect speakers

You can connect the speakers using the speaker cords.

	1
	2		3,4
	SPEAKERS
	RIGHT	LEFT
	Speaker	SPEAKER	Speaker
	cord	SPEAKER	cord
	cord	IMPEDANCE	cord
		6~16Ω
	Right speaker		Left speaker

1If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off.

2Hold the clamp of the speaker terminal.

3Insert the end of the speaker cord into the

terminal.

Match the polarity of the speaker terminals: ª to ª and

·to ·.

4Release your finger from the clamp.

IMPORTANT:

•Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

•DO NOT connect more than one speaker to one speaker terminal.

7

Image 10

JVC CA-UXB70 Connecting Speakers, 2Hold the clamp of the speaker terminal, 3Insert the end of the speaker cord into the

Contents

MICRO COMPONENT SYSTEM GVT0103-003BBINSTRUCTIONS UX-B70-Consistsof CA-UXB70and SP-UXB70REPRODUCTION OF LABELS Warnings, Cautions and OthersIMPORTANT FOR LASER PRODUCTS CAUTION Proper VentilationSAFETY INSTRUCTIONS Power sources PrecautionsInstallation IntroductionListening to FM and AM MW Broadcasts ContentsPlaying Back Discs on the 5-CDChanger Location of the Buttons and Controls Front PanelDisplay window Display window on the front panelCD ALL A - B TAPE Remote Control Unpacking Connecting AntennasGetting Started 1Attach the FM antenna to the FM 75 Ω3Insert the end of the speaker cord into the Connecting Speakers2Hold the clamp of the speaker terminal terminalTo remove the speaker grilles Connecting Other EquipmentPutting the Batteries into the Remote Control To connect audio equipmentOn the remote control ONLY Setting the ClockOn the remote control ONLY 1 Press CLOCK/TIMER CLOCK/TIMERTo turn on the unit, press STANDBY/ON Turning On the PowerTo turn off the unit automatically Auto Standby To activate the Auto Standby functionAHB BASS1 AHB BASS2 BASS OFF canceled Adjusting the VolumeOn the remote control To increase the volume, press VOLUME +press TREBLE to adjust the treble Adjusting the TonePress BASS to adjust the bass level or Press BASS to adjust the bass1 Tune in to the station you want to preset Tuning in to a StationPresetting Stations DOWN to select a preset numberPress DISC UP or DISC Tuning in to a Preset Station4 Press SET again On the remote control ONLYReceiving FM Stations with RDS PS Program ServiceTo search for a program using the PTY codes Changing the RDS InformationTo activate the Enhanced Other Networks function 1 Press TA/News/Info until the datatype you want flashes on the display NEWSLoading Discs Playing Back Discs on the 5-CDChangerOn the unit ONLY Basic Disc Operations 2 Select a disc to play On the remote controlPlaying Back All the Entire Discs -ContinuousPlay 1 Load discs into the 5-CDChanger“CD PROGRAM” appears on the Programing the Track Playing Order -ProgramPlay2 Press PLAY MODE repeatedly until On the remote control5 Program other tracks you want To check the program contentsPlaying at Random-RandomPlay 6 Press 3/8 CD2 Press SET at the starting point from Repeating Tracks or Discs-RepeatPlayProhibiting Disc Ejection which you want to repeat point APlaying Back Tapes When the tape direction isWhen the tape direction is Playing Back a TapeRecording on a Tape indicator lights up like-orRecording 2 Check the recording direction for the tapePress DISC UP or DISC DOWN On the unit remote control to select “1 CD.”Recording Discs -DiscSynchronized Recording Press DISC SELECT repeatedly4 Press CD REC MODE on the remote 2 Load discs into the 5-CDChangerDOWN control to select “ALL CD.”Press REC while playing the track control to select “1ST TRACK.”Press REC while “1ST TRACK” still you want to record1 Press CLOCK/TIMER Using the TimersUsing the Daily Timer and the Recording Timer How the timer actually works7 Adjust the clock if needed DOWN to set the volume levelthen press CLOCK/TIMER To deactivate the timer temporarily, pressPress SLEEP Using the Sleep TimerHow the Sleep Timer actually works On the remote control ONLYTo clean the disc MaintenanceCleaning the unit General NotesPossible Cause TroubleshootingSymptom ActionAdditional Information SpecificationsSupplied accessories Description of the PTY codes2003 VICTOR COMPANY OF JAPAN, LIMITED UX-B70MICRO COMPONENT SYSTEM0503MWMMDWJEM VICTOR COMPANY OF JAPAN, LIMITED