JVC DR-DX5SEK Results Of Auto Set Up/Preset Download Appearing, T-VLink Functions, On The Front Display Panel, PR +/–, Just Clock, Direct Rec, ATTENTION:, IMPORTANT:

	INITIAL SETTINGS EN 21
Results Of Auto Set Up/Preset Download Appearing	INFORMATION
On The Front Display Panel	Just Clock
	Your unit is equipped with the Just Clock function which provides
If both Auto Channel Set and	accurate time keeping through automatic adjustments at regular
	intervals, by reading data from a PDC signal. If you want to take
Auto Clock Set have been
	advantage of this function, simply set it to AONB. (A pg. 77)
performed successfully, the
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all	If you have any difficulty with the above procedures call the JVC
necessary stations have been stored in the unit’s memory by using	Customer Service Hot Line on 0870 330 5000.
the PR +/– button(s).
● If station names (ID – A pg. 88) have also been stored in the	T-V Link Functions
unit’s memory, the station name will be displayed at the top right
corner of the TV screen for about 5 seconds when the unit is	When you connect the unit to your TV via a fully-wired 21-pin
tuned to a different station.
	SCART cable (A pg. 18), the following functions are available. You
● If you want to set the tuner manually such as to add or skip
	can use these functions only with a TV offering T-V Link, etc.*
channels, to change channel positions, or to set or change
	For details, refer to the instruction manual of your TV.
station names, see pages 75 – 76.
	* Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK,
If Auto Channel Set has	Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable. The degree
succeeded but Auto Clock Set	of compatibility and available functions may differ by system.
has not, APR 1B (channel	TV Auto Power On
position) is displayed.	The TV will turn on and be set to its AV mode automatically
OR	whenever you start playback.
	For details, refer to the instruction manual of your TV.
If both Auto Channel Set and Auto Clock Set have failed,
	Unit Auto Standby
A– –:––Bis displayed.
	You can use your TV’s remote control to turn off the unit.
A Turn on the TV and select its AV mode, then make sure that all
	For details, refer to the instruction manual of your TV.
necessary stations have been stored in the unit’s memory by
using the PR +/– button(s).	Direct Rec
● If station names (ID – A pg. 88) have also been stored in the	You can easily start recording the programme that you are
unit’s memory, the station name will be displayed at the top right	watching on your TV. When you use this function, set ADIRECT
corner of the TV screen for about 5 seconds when the unit is	RECB to AONB. (A pg. 72)
tuned to a different station.
● If you want to set the tuner manually such as to add or skip
channels, to change channel positions, or to set or change
station names, see pages 75 – 76.
B Perform AClock SetB (A pg. 77).
ATTENTION:
After making sure the cables are connected properly, turn off the
unit’s power once, then turn the unit’s power back on again.
Perform AAuto Set UpB (A pg. 19) or APreset DownloadB
(A pg. 20) again.

IMPORTANT:

●To check if the Guide Programme numbers have been set correctly, perform the VIDEO Plus+ Timer Programming. (A pg. 46)

●In certain reception conditions, station names may not be stored correctly, and auto Guide Programme Number Set may not work properly. If the Guide Programme numbers are not set properly when you timer record a TV programme using the VIDEO Plus+ system, the unit will record a TV programme of a different station. When programming the timer using the VIDEO Plus+ system, be sure to check the desired channel is selected correctly.

(A pg. 46)

●Your unit memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture. (A pg. 76, ADelete A ChannelB)