￿Functions, Contents, and Adjustment Range of items

FUNCTION SETTING

Sets the control systems for the COLOR SYSTEM, synchronized signal, RUSH DELAY TIME, colors and functions of the tally lamp, groups of the audio output modes, and MAKE/ TRIGGER terminal.

•Can be also used to adjust the zooming position of the picture for the component signal input, and check the amount of time that the monitor has been used.

￿COLOR SYSTEM Selects the color system.

AUTO:Changes NTSC and PAL automatically.

NTSC:Keeps the color system NTSC.

PAL: Keeps the color system PAL.

NOTE:

Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL.

￿SYNC SELECT

Selects the synchronized signal.

INT.: The input video signal is synchronized with the built-in sync signal.

EXT.: The input video signal is synchronized with an external signal from an external sync terminal.

￿RUSH DELAY TIME

Sets the delay time between when the stand-by button is pressed and when the monitor actually turns on.

STD.: Power turns on about 1 second after the stand-by button is pressed.

SLOW: Power turns on about 3.2 seconds after the standby button is pressed.

NOTE:

It is recommended to apply “SLOW” to some of the monitors if you need to turn on multiple monitors at the same time. You can control the rush current of the entire system.

￿TALLY SELECT

Selects the color of the tally lamp on the upper right of the front panel.

GREEN:The tally lamp lights in green.

￿FORMAT IND.

Sets the tally lamp as the format indicator to show the format of the signal currently input.

NOTE:

When setting FORMAT IND. to ON, you cannot use the tally lamp function of the MAKE/TRIGGER terminals.

☞page 19

ON: Uses the lamp as the format indicator. Green: Shows the HD SDI signal is input. Red: Shows the SD SDI signal is input. Orange: Shows the composite signal is input.

OFF: Uses the lamp as the tally lamp.

☞page 19

￿REMOTE SYSTEM

Sets the MAKE/TRIGGER terminal.

☞“How to Use the MAKE/TRIGGER Terminal” on page 19

CONTROL FORM:

Selects the control system for the MAKE/TRIGGER terminal.

MAKE: Selects the make contact system as the external control method.

TRIG.: Selects the trigger system as the external control method.

SET: You can apply the functions to the 1st to 6th pin terminals of the MAKE/TRIGGER terminal as you want.

PORT F1 – PORT F6:

Selects the function to be applied to the 1st to 6th pin terminals of the MAKE/TRIGGER terminal.

☞“How to Use the MAKE/TRIGGER Terminal” on page 19

NOTE:

You can set “PORT F1” – “PORT F6” only when “CONTROL FORM” is set to “SET.”

￿ZOOM WINDOW

Adjusts the horizontal position of the zooming area. This item appears on the menu only when using the Component Unit (option).

•–30 O 00 O +30

–:Moves the horizontal position of the zooming area to the left.

+: Moves the horizontal position of the zooming area to the right.

￿E. AUDIO GROUP

Sets the group of the available audio output modes selected by the MENU control.

This item appears on the menu only when using the Multi-Format SDI Unit (option).

RED: The tally lamp lights in red.

NOTES:

1G: 1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch

•“TALLY SELECT” does not appear on the menu when both the following conditions are applied:

–When selecting “TA. SEL” to a pin terminal of the MAKE/ TRIGGER terminal in “REMOTE SYSTEM” of SET-UP MENU.

–When activating the external control.

☞page 19

•The tally lamp is controled using the MAKE/TRIGGER terminal of the REMOTE (external control) terminals.

☞page 19

2G: 5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch

1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 1-2ch

1-2G:

AUTO 5-8ch 1-4ch 7-8ch 5-6ch 3-4ch

•When HD/SD SDI signal including EMBEDDED AUDIO signal is input, you can select the channel of the audio signal output from the audio output terminal by changing the audio output mode. Refer also to the Multi-Format SDI unit’s manual.

15