How to Use SET-UP MENU (cont.)

STATUS DISPLAY

Sets the items related to the display screens, such as the status display or the AUDIO LEVEL METER display.

• Can also be used to set the 1080/60i or 1035/60i signal displayed correctly.

￿STATUS DISPLAY Sets the status display.

• AUTO/MANUAL/OFF

☞ “About the status display” on page 5

￿1080/1035

When the component signal is input, the monitor does not automatically discriminate the 1080/60i signal from the 1035/60i signal. Set this item according to the input signal format.

This item appears on the menu only when using the Component Unit (option).

• 1080/1035Setting the AUDIO LEVEL METER display

You can check the conditions of the current EMBEDDED AUDIO signals on the AUDIO LEVEL METER display.

AUDIO LEVEL METER display exampleLEVEL METER ch: 1-8, BAR TYPE: 3COLORS

OVER LEVEL [–10dB/–8dB/–6dB/–4dB/–2dB]

REFERENCE LEVEL [–20dB/ –18dB]

1 2 3 45 6 7 8

Audio channels and OVER/REFERENCE LEVEL indication

The following items are the settings for the AUDIO LEVEL METER display.

The following items appear on the menu only when using the Multi-Format SDI Unit (option).

￿LEVEL METER ch

Selects the audio channels used in the AUDIO LEVEL METER display.

• OFF/1:2/12:34/31:24/123:456/1-8

NOTES:

•This item does not appear on the menu when both the following conditions are applied:

–When selecting “L. METER” to a pin terminal of the MAKE/ TRIGGER terminal and “MAKE” to “CONTROL FORM” of “REMOTE SYSTEM” in SET-UP MENU.

–When activating the external control.

☞ “REMOTE SYSTEM” on page15 and page 19

•Numbers indicate the audio channel. The channel input level indicated on the left side of “:” is displayed on the left side of the screen, and the channel input level indicated on the right side of “:” is displayed on the right side of the screen.

•The AUDIO LEVEL METER display does not appear when this item is set to OFF.

•When “1-8” is selected, the channel input level for 1, 2, 3 and 4 is displayed on the left side of the screen, and the channel input level for 5, 6, 7 and 8 is displayed on the right side of the screen.

•The AUDIO LEVEL METER display moves to inside of the screen when the ZOOM function is operated.

￿BAR TYPE

Selects the color of the AUDIO LEVEL METER display.

W. 100: White color display

W. 50: White (half transparent) display

3COLORS:

The AUDIO LEVEL METER display uses three different colors (red, yellow and green) to indicate variations in input levels.

Red: Displayed when the audio input is at the same level set in “OVER LEVEL” or higher.

Yellow: Displayed when the audio input is at the same level set in “REFERENCE LEVEL” or higher.

Green: Displayed when the audio input is lower than the level set in “REFERENCE LEVEL.”

NOTES:

•For W. 100 and W. 50, the line indication for the standard input level set in the “REFERENCE LEVEL” is displayed. Input level set in the “OVER LEVEL” is not displayed.

•As for the audio channel bar display with no signal input, white is displayed for the 3COLORS setting, and gray is displayed for other settings.

￿BAR BRIGHTNESS

Selects the brightness of the AUDIO LEVEL METER display.

HIGH: Brighter

LOW: Darker

￿REFERENCE LEVEL

Sets the standard input level.

•–20dB/–18dB

￿OVER LEVEL

Sets the input level’s lower limit indicated in red for the “3COLORS” display.

•–10dB/–8dB/–6dB/–4dB/–2dBCONTROL LOCK

￿CONTROL LOCK

Prohibits the monitor operations except turning on/off the monitor and deactivating this function.

•Operating the monitor by the external control is available if this function is activated.

ON: Activates this function.

OFF: Deactivates this function.

NOTE:

•When “CONTROL LOCK” is set to “ON,” “ Control lock on!” appears on the screen if you try to operate the monitor.

all reset

Resets all SET-UP MENU items to factory-preset values.

1.Move the MENU control to / to select “all reset,” then move it to . Confirmation message is displayed.

2.To initialize, move the MENU control to .

To cancel the initialization, press the MENU control.

18