JVC GET0634-006A In-dash mounting / 裝設、固定在儀表板內, Removing the unit / 拆卸本機, Part list / 零件清單

	KD-R516/KD-R515
	Installation/Connection Manual
	安裝/連接手冊
GET0634-010A	1209DTSMDTJEIN
[UT]	EN, CT
	© 2009 Victor Company of Japan, Limited

ENGLISH / 中文

You need the installation kits which corresponds to your car. /	Check the battery system in your car /
您需要與您的汽車相配套的安裝元件。	查看汽車的電池系統

To the car system /

接至汽車系統

12 V DC, NEGATIVE ground /

直流 12 V，負極接地

WARNINGS / 警告

•To prevent short circuits:

–Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

–Cover the terminals of the UNUSED leads with insulating tape.

•Be sure to ground this unit to the car’s chassis again after installation.

•Replace the fuse with one of the specified rating.

•Connect speakers with a maximum power of more than 50 W (impedance of 4 Ω to 8 Ω). Otherwise, change the <AMP GAIN> setting. (See page 15 of the INSTRUCTIONS.)

•The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

•為防止短路：

-在安裝本機之前，拔開電池的負極端子，並把所有電路都連接好。

-請用絕緣帶包住未使用導線的端子。

•安裝完畢後務必將本機的地線重新接至車身。

•將保險絲更換為額定負荷值的保險絲。

•連接最大功率大於 50 W 的揚聲器（阻抗為 4 Ω – 8 Ω）。 否則，請切換 <AMP GAIN> 設定。 （參閱使用 說明書的第 15 頁。）

•本機使用後，散熱片會很熱。因此，在移出本機時，小心不要觸摸散熱片。

Heat sink / 散熱片

INSTALLATION / 安裝

The following illustration shows a typical installation. If you have any questions or require information	下面的圖解表示了典型的安裝程序。如果您有問題，或需要有關配套元件的資料，請向 JVC
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.	汽車音響分銷商或配套元件供應公司詢問。

In-dash mounting / 裝設、固定在儀表板內

Do the required electrical connections.	Install the unit at an angle of
進行所需的電路連接。
	less than 30˚.
	將本機安裝在少於 30° 的
	角度。

Part list / 零件清單

AHard case / 硬盒 (×1)

BControl panel / 控制面板 (×1) C Sleeve / 外套機殼 (×1)

D Trim plate / 裝飾框 (×1)

E Power cord / 電路連接用的配

線束 (×1)

F Handles / 板條型把手 (×2)

Bend the appropriate tabs to hold the sleeve firmly in place.

*1弄彎機殼的突舌，把外套機殼牢固在儀表板內。

When installing the unit without using the sleeve / 若不使用外套機殼安裝本機

Flat head screws (M5 × 8 mm) / 平頭螺絲釘（M5 × 8 mm）*2

Pocket / 空殼

Bracket / 托座 *2

Removing the unit / 拆卸本機

Release the rear section first... / 首先將本機後背部分鬆開...

*1	When you stand the unit, be careful not to damage the fuse on the rear.	*1	您豎起本機時，小心不要損壞底部的保險絲。
*2	Not supplied for this unit.	*2	不隨本機提供。

1