60 EN | USING THE REMOTE CONTROL UNIT (cont.) |
Select Scenes
FADE/WIPE
PLAY
● If the search time for an |
5 minutes, the recording deck’s |
mode will be cancelled and editing will not take |
place. |
● If there are blank portions before or after the Edit- |
In and |
included in the edited version. |
EFFECT
PAUSE
EDIT IN/OUT
R.A.EDIT 
ON/OFF
CANCEL VCR REC STBY
6Press PLAY (U) and then press R.A.EDIT ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
7 If using a Wipe/Fader at the beginning of the scene, press FADE/WIPE on the remote control. ● Cycle through the
effects by pressing repeatedly, and stop
when the one you want is displayed.
●You cannot use a Picture Wipe/Dissolve at the beginning of Program 1.
8At the beginning of the scene, press EDIT IN/ OUT on the remote control. The
9At the end of the scene, press EDIT IN/OUT. The
10If using a Wipe/Fader at the end of the scene, press FADE/WIPE.
●Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed.
●If you select a Wipe/Fader effect for an
●You cannot use a Picture Wipe/Dissolve at the end of the last scene.
●When you use Fader/Wipe effects, that time is included in the total time (this does not apply to Picture Wipe/Dissolve).
11If using Playback Special Effects, press EFFECT. ( pg. 56)
12Repeat steps 8 through 11 to register additional scenes.
●To change previously registered points, press CANCEL on the remote control. The registered points disappear, one at a time, from the most recently registered point.
●If you are not using Wipe/Fader or Program AE with special effects, repeat steps 8 and 9 only.
NOTES:
●When choosing a scene, set
● Since time codes register time only as accurately |
as seconds, the time code total time may not |
match the total program time exactly. |
● Turning off the camcorder’s power erases all |
registered |
● If you select Sepia or Monotone mode from |
Program AE with special effects, you cannot use |
the Dissolve or Black & White Fader. In this case |
the Dissolve or Black & White indicator begins |
blinking. Once the next |
the effect is turned off. To combine these effects, |
use Sepia or Monotone during recording, then use |
the Dissolve or Black & White Fader during |
Random Assemble Editing. |
● It is not possible to use Wipe/Fader effects and |
Program AE with special effects during Random |
Assemble Editing using a DV cable. |
Picture Wipe And Dissolve Menu (available only for Random Assemble Editing) You can use not only the wipe/fader effects on page 32 but also the picture wipe and dissolve effects below.
DISSOLVE: The new scene gradually appears as the old one gradually disappears.
WIPE – CORNER: The new scene wipes in over the previous one from the upper right corner to the lower left corner.
WIPE – WINDOW: The next scene gradually wipes in from the centre of the screen toward the corners, covering the previous scene.
WIPE – SLIDE: The next scene gradually wipes in over the previous one from right to left.
WIPE – DOOR: The previous scene wipes out from the centre to the right and left, like a door being pushed open to reveal the next scene.
WIPE – SCROLL: The new scene wipes in over the last one from the bottom of the screen to the top.
WIPE – SHUTTER: The new scene wipes in over the previous one from the centre toward the top and bottom of the screen.
Automatic Editing To VCR
13Rewind the tape in the camcorder to the beginning of the scene you want to edit and press PAUSE (9).
14Press VCR REC STBY (79), or manually engage the VCR’s
15Press the Recording Start/Stop Button on the camcorder. Editing proceeds as programmed, right through to the end of the last registered scene.
