Access Mode SET Screen, EN Playback | JVC HR-J313EU instruction

16ENPLAYBACK(cont.)

Repeat Playback

Your video recorder can automatically play back the whole tape 50 times repeatedly.

Picture Control

This feature helps you to adjust the playback picture quality according to your preference. *The default setting is "AUTO."

1		START PLAYBACK
1	Press PLAY.
2		ACTIVATE REPEAT PLAYBACK
	Press PLAY and hold for over 5 seconds, then release.
		● The Play indicator ( ) on the display panel blinks
		● The Play indicator ( ) on the display panel blinks
		slowly.
		● The tape plays 50 times automatically, and then
		stops.

3		STOP PLAYBACK
3	Press STOP at any time to stop playback.

NOTE:

Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback.

	ACCESS MAIN MENU
	SCREEN
1 Press MENU.
	ACCESS MODE SET
	SCREEN
Move the highlighted bar (pointer) to "MODE SET" by
2 pressing %Þ, then press OK or #.
	SELECT PICTURE
	CONTROL SET MODE
	Move the highlighted bar	MODE SET
	(pointer) to "PICTURE	B. E. S. T.	ON
	CONTROL" by pressing	B. E. S. T.	ON
	CONTROL" by pressing	PICTURE CONTROL	AUTO
3 %Þ, then press OK or #to		AUTO TIMER	OFF
	select the desired mode.	O. S. D.	ON
	select the desired mode.	DIRECT REC	ON
	AUTO: Provides	POWER SAVE	OFF
	optimised picture	AV2 SELECT	AV2
	optimised picture	NEXT PAGE
	benefits of B.E.S.T.	NEXT PAGE
	benefits of B.E.S.T.	[5°] =
	Picture System.	[MENU] : EXIT
	Normally select
	AUTO.
	EDIT: Minimizes picture degradation during editing
	(recording and playback).
	SOFT: Reduces image coarseness when viewing
	overplayed tapes containing a lot of noise.
	SHARP: Clearer, sharper-edged picture when viewing
	images with lots of flat, same-coloured surfaces
	such as cartoons.

NOTES:

●When you select EDIT, SHARP or SOFT, the selected mode will not change until you select again.

●When you select EDIT to dub tapes, be sure to select AUTO after you finish dubbing the tapes.

RETURN TO NORMAL

SCREEN

4 Press MENU.

NOTES:

●When B.E.S.T. is OFF, "PICTURE CONTROL" switches automatically from AUTO to NORM.

●Select EDIT when you are dubbing tapes. Refer to page 30.

Image 16

JVC HR-J313EU specifications Access Mode SET Screen, Select Picture Control SET Mode, EN Playback, Repeat Playback

Contents

HR-J313EU For Italy Safety PrecautionsDo not place the recorder Check Contents Basic ConnectionsSituate Recorder Connect Recorder to Mains Auto Set Up EN Initial SettingsIf you are referring to the front display panel If you are referring to the on-screen display Language Code Via an RF cable only RF connectionYour TV to the Video Channel. Refer to This Preset Download ENU If both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock on Language Access Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal Screen Power Save Mode TV Auto Power On Link FunctionsLI NK NexTView Link Colour System Set ModeAbout Ntsc Playback Counter and tape remaining time readings will be incorrect Basic Playback Load a CassettePoint Start Playback Playback Playback FeaturesSearch Adjust Tracking Override Automatic TrackingManually Return to Automatic Access Mode SET Screen Select Picture Control SET ModeEN Playback Repeat Playback Basic Recording Recording Features Reset CounterSelect Channel to Watch Display Remaining Time Engage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorder S.T. Picture System PreparationS.T., then press OK or #to set to on or OFF Playback RecordingOr press Record on the recorder Timer Programming EN Timer Recording Timer Warning Satellite Tuner Users Express Timer Programming Start TimeEnter Programme Stop Time SET VPS/PDC Mode If no VPS/PDC signal is detected from the station, VPSVPS/PDC Recording Press TV Prog + Check, Cancel And Replace Programmes Press ä TimerPress Again to check More information. Each Time you press Next programmes Auto Timer Auto TIMER, then pressOK or #to select either On or OFF Select AV2 Select Mode REC Link indicatorAutomatic Satellite Programme Recording Before performing the following steps SET Edit Mode Edit From a CamcorderMake Connections SET RECORDER’S Input Input Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source Player AV2 Select Setting AV2 IN/DECODER connectorRecorder Press %Þ to move the highlight bar pointer to AV2 Select Connection To Satellite Tuner EN System ConnectionsSatellite Tuner Unit Back of TV Decoder Set AV2 Select to AV2. pg Connecting Using a Decoder Select Input ModeConnect Decoder SET Tuner Showview Setup Subsidiary Settings ENNumber Enter Receiving Channel Position Number Access Auto CH SET EN SU Bsidiary SettingsTuner Set Auto Channel Set Perform Auto Channel SET View Confirmation Screen SU Bsidiary Settings Storing Channels Manually When Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Press %Þ @ #until the item you want to move begins Access Manual Channel SET Screen Perform TuningAccess Manual Switch Stations TV Station And ID List Turn the Recorder on Clock SetSET Date and Time Default setting is OFF. Set as desired by pressing Recorder is preset to receive clock settingSET Just Clock Channel position to the number representing Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET RF Output System Troubleshooting EN Timer Recording Roubleshooting Ä remain lit on the display panel. Is there Problem? Quest Ions and Answers EN Index Front View Rear View EN Index VCR, TV Prog +/-,TV +/-, TV Muting Rotary two-head herical scan Speci FicationsIN/OUT x 1, IN/DECODER x Auto Set Up referring to the display panel Ex. Francais is selected for Belgium