37

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIMER RECORDING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

1.

Timer recording won’t work.

The clock and/or the timer have

Check or re-perform the clock/timer

 

 

 

 

 

 

 

been set incorrectly.

settings to ensure correctness.

 

 

 

 

 

 

 

The timer is not engaged.

Press TIMER and check to make sure

 

 

 

 

 

 

 

 

 

 

that TIMER appears on the front

 

 

 

 

 

 

 

 

 

 

display panel.

 

 

 

 

 

 

 

The VCR has not been set up properly.

Re-perform the set-up procedures.

 

 

 

 

 

 

 

 

2.

On-screen timer programming

Timer recording is in progress.

Timer programming can’t be performed

 

 

 

won’t work.

 

 

 

when timer recording is in progress.

 

 

 

 

 

 

 

 

 

 

Wait until it finishes.

 

 

 

 

 

 

 

 

3.

TIMER and ] on the front

The timer is engaged but there’s no

Load a cassette with the record safety

 

 

 

display panel won’t stop blinking.

cassette loaded.

tab intact, or with the hole covered

 

 

 

 

 

 

 

 

 

 

with adhesive tape.

 

 

 

 

 

 

 

 

4.

The cassette is automatically

The loaded cassette has had its

Remove the cassette and cover its

 

 

 

ejected, and TIMER and ] on the

record safety tab removed.

hole with adhesive tape, or replace it

 

 

 

front display panel won’t stop

 

 

 

with a cassette on which the safety

 

 

 

blinking.

 

 

 

tab is intact.

 

 

 

 

 

 

 

 

5.

TIMER blinks for 10 seconds and

TIMER has been pressed when there

Check the programmed data and re-

 

 

 

the timer mode is disengaged.

are no programs in memory, or the

program as necessary, then press

 

 

 

 

 

 

 

timer record program information

TIMER again.

 

 

 

 

 

 

 

has not been programmed correctly.

 

 

 

 

 

 

 

 

 

 

 

 

6.

The cassette is automatically

The end of tape was reached during

The program may not have been

 

 

 

ejected, the power shuts off and

timer recording.

recorded in its entirety. Next time

 

 

 

TIMER and ] won’t stop

 

 

 

make sure you have enough time on

 

 

 

blinking.

 

 

 

the tape to record the entire program.

 

 

 

 

 

 

 

 

 

 

 

 

OTHER PROBLEMS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

1.

When scanning channels, some of

Those channels have been preset to

If you need the skipped channels,

 

 

 

them are skipped over.

be skipped.

restore them (pg. 10).

 

 

 

 

 

 

 

 

2.

The channel can’t be changed.

Recording is in progress.

Press PAUSE to pause the recording,

 

 

 

 

 

 

 

 

 

 

change channels, then press PLAY to

 

 

 

 

 

 

 

 

 

 

resume recording.

 

 

 

 

 

 

 

3. "--:--" is displayed on the front

The lithium battery is exhausted.

Replace the lithium battery with a

 

 

 

display panel after a power outage.

 

 

 

new one. (pg. 5)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ATTENTION:

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the power off and unplug the power cord. Then plug it in again and switch power on. Take out the cassette. After checking the cassette, operate the unit as usual.

Page 37
Image 37
JVC HR-J6004UM Timer again, Has not been programmed correctly Cassette is automatically, When scanning channels, some