JVC HR-S6600EK setup guide Access Main Menu Screen

33

REC LINK SP/LP

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

●When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the button does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 18) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder's AV2 IN/DECODER connector. (☞ pg. 32)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

ACCESS MAIN MENU SCREEN

1 Press MENU.
	ACCESS MODE SET SCREEN
	Move the highlight bar (pointer) to "MODE SET" by
2 pressing %Þ, then press OK or%.
3	SELECT AV2 SELECT MODE
	Move the highlight bar (pointer) to "AV2 SELECT", by
	pressing %Þ, then press OK or%to set to "SAT".
		MODE SET		PREVIOUS PAGE
		B. E. S. T.	ON	S-VHS	AUTO
		PICTURE CONTROL	AUTO	AV1 SELECT	VIDEO
		AUTO TIMER	OFF	AV2 SELECT	SAT
		O. S. D.	ON
		DIRECT REC	ON
		AUTO SP=LP TIMER	OFF
		POWER SAVE	OFF
		NEXT PAGE
	[5°] =			[5°] =
		[MENU] : EXIT		[MENU] : EXIT
	SET TAPE SPEED
4 Press SP/LP ( ) to set the tape speed.
	ENGAGE AUTO SATELLITE PROG
5	REC MODE
	Press and hold REC LINK for about 2 seconds. The
	button lights up and the recorder turns off automatically.

●To disengage the Auto Satellite Prog Rec mode, press REC LINK. The button's light goes off.

●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

NOTES:

●Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (☞ pg. 25).

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

●The button's light blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

●If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording.

●The B.E.S.T. system (☞ pg. 22) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 39) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the button's light blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN/DECODER connector.