—23—
CChange code for VCR
Press any key on the Remote. The VCR now responds to B code
control signals.
●To set the Remote and the VCR to transmit and respond to A
code control signals, repeat above procedure as shown above
except press the Number key “1” in step B of 1
11
1.

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control
code for the Remote between A and B (墌 step A
AA
A), keeping two
VCRs to different control codes.
●To change only the remote control code for the Remote, DO
NOT perform steps B
BB
B and C
CC
C.

Editing from Camcorder

You can use a camcorder as the playback unit and your VCR as the
recording VCR. Refer also to the camcorder’s instruction manual
for connection and its operations.
AMake connections
●When the JVC camcorder is equipped with the Master Edit
Control, you can control the VCR from the camcorder. Connect
the mini-plug cable (not supplied with this VCR) as illustrated.
●If camcorder is monaural, connect the audio output connector
on the camcorder to the left audio input connector on this VCR.
BLoad cassettes
Insert the playback cassette into the camcorder and the cassette to
be recorded on into this VCR.
CSelect input location on this VCR
Select the correct external input location on this VCR.
Select “L-1” —when connecting the camcorder to the audio/video
(or S-video) input connectors on the rear panel.
Select “F-1” —when connecting the camcorder to the audio/video
(or S-video) input connectors on the front panel.
On the VCR
Press CH+/– or push the ADVANCED JOG dial, then turn it to the
left or right until “L-1” or “F-1” appears on the display panel.
On the Remote
Press AUX and/or CH+/– until “L-1” or “F-1” appears on the
display panel.
DSelect video input connector
Select the appropriate mode depending on the connector being
used (墌pg. 21).
When using S-VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “S-VIDEO”.
When using S-VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “S-VIDEO”.
When using VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “VIDEO”.
When using VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “VIDEO”.
ESelect edit mode
Set “PICTURE CONTROL” to “EDIT” (墌pg. 20).
FSet AV COMPU-LINK mode
If your JVC camcorder is equipped with a Master Edit Control, set
“AV COMPU-LINK” to “OFF” (墌pg.21). The REMOTE PAUSE/
AV COMPULINK connector works as a Remote Pause connector.
GStart playback
Set the camcorder to its play mode.
NOTE:
If the camcorder is equipped with a superimpose/OSD disable
feature, set it to “OFF” before starting playback.
HStart recording
On the VCR
Press REC (7).
On the Remote
While holding REC (7), press PLAY (4).
●If you are using a Master Edit Control-equipped JVC camcorder,
recording starts automatically on this VCR. (Refer to camcorder’s
instruction manual.)
NOTE:
Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM”
when “VIDEO CALIBRATION” is set to “OFF”) after you finish
dubbing the tapes. (墌pg. 20)
Editing
Various connection for editing tapes
The following three methods can be used for editing tapes.
●VHS to S-VHS editing (VIDEO-VIDEO connection):
Although the picture quality is inherently limited by the original
VHS quality, the edited tape has better picture quality than
those made by VHS-to-VHS editing.
●S-VHS to VHS editing (VIDEO-VIDEO connection):
Since the original source is recorded in S-VHS mode, the edited
tape has better picture quality than those made by VHS-to-VHS
editing.
●S-VHS to S-VHS (S-VIDEO connection):
Original picture quality of S-VHS made can be duplicated with
minimal picture degradation. This is the best editing method
you can use on S-VHS VCRs.
To S-video output
This VCR (for recording)
Camcorder
(for playback)
S-video cable
(supplied)
To AUDIO/VIDEO
input To S-VIDEO input
Audio/video cable
(supplied)
To audio/video
output
To ED IT
To rear panel
REMOTE PAUSE/
AV COMPULINK
Mini-plug cable
(not supplied)
(JVC camcorder only)
HR-S9911U-EN.fm Page 23 Monday, April 22, 2002 1:34 PM