DConnect Controller to VCR
Connect the Controller to the CABLE BOX Controller connector on the rear panel.
ETurn on cable box or DBS receiver
Select a channel other than channel 9 on your cable box, or channels 100, 205 on your DBS receiver.
FAccess Main Menu screen, then Initial Set screen on VCR
Press MENU on the Remote. Press rt to move the highlight bar (arrow) to “INITIAL SET”, then press OK or e.
G Access Cable Box Set screen or DBS
Receiver Set screen
Press rt to move the highlight bar (arrow) to “CABLE BOX SET” or “DBS RECEIVER SET”, then press OK or e.
H Select output channel
Your selection depends on how the unit is connected to your VCR.
●If the unit is connected to your VCR’s
ANTENNA IN terminal on the rear
panel, Press rt until the channel number representing the cable box’s
output (CH2 – CH9) or DBS receiver’s output (CH3 or CH4) appears on the screen.
●If the unit is connected to your VCR’s AUDIO/VIDEO IN connectors on the front panel, press rt until “ON
●If the unit is connected to your VCR’s AUDIO/VIDEO IN connectors on the rear panel, press rt until “ON
●If you do not use any unit, press rt until “OFF” appears on the screen.
IAccess Brand Set screen
Press OK or e.
●If the Clock Set screen appears, perform “Manual Clock Set”
( pg. 7). If you press MENU after the clock has been set, the Brand Set screen appears.
J Enter brand code and perform test
Press the appropriate Number keys on the Remote to enter the brand code from the following list, then press OK or e.
CABLE BOX BRAND | CODE |
|
|
ARCHER | 1, 5, 17 |
CABLETENNA | 1, 17 |
CABLEVIEW | 15, 16, 17, 21, 25 |
CITIZEN | 15, 16, 17, 21, 25 |
CURTIS | 2, 8 |
DIAMOND | 1, 17 |
GC BRAND | 15, 16, 17, 21, 25 |
GEMINI | 15 |
GENERAL INSTRUMENTS | 1, 4, 6, 11, 12, 15, 28 |
HAMLIN | 10, 18, 23 |
JASCO | 15 |
JERROLD | 1, 4, 6, 11, 12, 15, 28 |
NOVAVISION | 2, 8 |
OAK | 7, 20 |
PANASONIC | 13, 14 |
PULSER | 15, 16, 17, 21, 25 |
RCA | 13, 14 |
REGAL | 10, 18, 23 |
REMBRANDT | 1, 16, 17 |
SAMSUNG | 5, 16, 24 |
SCIENTIFIC ATLANTA | 2, 8 |
SIGMA | 7, 20 |
SL MARX | 5, 16, 17, 24, 25 |
SPRUCER | 13, 14 |
STARGATE | 5, 15, 16, 17, 21, 24, 25 |
TELEVIEW | 5, 16, 24 |
TOCOM | 1, 4, 16 |
UNIKA | 1, 17 |
UNIVERSAL | 16, 17, 25 |
VIDEOWAY | 3, 9, 22 |
ZENITH | 3, 9, 22 |
|
|
DBS RECEIVER BRAND | CODE | DBS RECEIVER BRAND | CODE |
|
|
|
|
JVC (DISH Network) | 51 | SONY (DSS) | 41 |
ECHOSTAR (DISH | 51 | RCA (DSS) | 40 |
Network) |
|
|
|
|
|
|
|
For cable box
●If the cable box’s channel changes to 9, setting is complete. Press OK.
● If the cable box’s channel does not change to 9;
A Press rt to move the highlight bar (arrow) to “NO”, then press OK or e.
BRepeat step 0 until the cable box’s channel changes to 9 by entering another code.
CIf the channel does not change after going through all the code
numbers listed for your model of cable box, then try all the other numbers.
For DBS receiver
●If the DBS receiver’s channel changes to the channel listed below for your brand,
setting is complete. Press OK or e.
JVC | ] 100 | SONY ]205 |
ECHOSTAR ] 100 | RCA ]205 | |
●If the DBS receiver’s channel does not change as shown above;
APress rt to move the highlight bar (arrow) to “NO”, then press OK or e.
BRepeat step 0.
Playback
Basic Playback
●Turn on the VCR and TV, and select the VCR channel (or AV mode).
●Set the VCR/TV/CABLE/DBS selector on the Remote to “VCR”.
ALoad a cassette
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR.
●Do not apply too much pressure when inserting.
●The VCR turns on automatically.
●The tape will run for a few seconds while the VCR searches for the tape number.
●If the cassette’s record safety tab has been removed, playback begins automatically.
NOTE:
When you use the Video Navigation function, operate the VCR only after the tape number is detected; otherwise, you cannot use the Video Navigation function.
BStart playback
Press PLAY (4).
●The
CONTINUED ON NEXT PAGE
— 9 —
