JVC HR-S9911U specifications Specifications, Locate end point, Start editing

ELocate end point

Load the cassette to be edited into the VCR and press PLAY (4). Press PAUSE (9) when you find the end of the scene that you want to edit.

Press C.RESET so that the counter reading becomes “0:00:00”.

●You can also use FF (5), the ADVANCED JOG dial on the VCR, or the JOG dial/SHUTTLE ring on the Remote to locate the end point.

FLocate start point, and engage Insert Editing mode

Use REW (3), the ADVANCED JOG dial on the VCR, or the JOG dial/SHUTTLE ring on the Remote to rewind the tape. Press PAUSE (9) when you find the beginning of the scene for which you want to edit, then press INSERT.

●The VCR enters the Insert Editing Pause mode. “o”, “u” and “i” light up on the display panel.

●If you want to perform AV Dubbing and replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time, after you press INSERT, press A.DUB also. “o” and “u” blink, and “i” lights up on the display panel.

GStart editing

Load the source cassette and engage the Play mode of the other component, then press PLAY (4) on the VCR. Insert Editing begins. “o” and “u” light up on the display panel.

●Insert Editing stops automatically when the counter reaches “0:00:00”, and the VCR enters the Play mode.

To stop editing any time during recording

Press STOP (8) on the Remote or STOP/EJECT (0) on the VCR, then engage the Stop mode of the other component. Press REC (7) on the recording VCR.

NOTES:

●Be sure to select “AUTO” for “PICTURE CONTROL” (or

“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish editing. ( pg. 20)

●Editing is not possible with a cassette whose record safety tab has been removed.

●The recording speed (SP/EP) is determined by the previous recording to be replaced. If the recording speed changes on the tape to be edited while editing the tape, the inserted picture will be distorted where the recording speed changes.

●When you edit a tape, a small portion of the recording preceding to the editing start point will be erased from the edited tape.

Specifications

GENERAL

Power requirement	: AC 120 Vd, 60 Hz
Power consumption
Power on	:	26 W
Power off	:	2.5 W
Temperature
Operating	:	5°C to 40°C (41°F to 104°F)
Storage	:	–20°C to 60°C (–4°F to140°F)
Operating position	:	Horizontal only
Dimensions (W x H x D) :		435 mm x 105 mm x 343 mm
		(17-3/16" x 4-3/16" x 13-9/16")
Weight	:	4.9 kg (10.8 lbs)
Format	:	S-VHS/VHS NTSC standard
Maximum recording time
SP	:	210 min. with ST-210 video cassette
EP	:	630 min. with ST-210 video cassette

VIDEO/AUDIO

Signal system	: NTSC-type color signal and EIA
		monochrome signal, 525 lines/
		60 fields
Recording/Playback	: DA-4 (Double Azimuth) head helical
system		scan system
Signal-to-noise ratio	:	45 dB
Horizontal resolution
VHS	:	230 lines
S-VHS	:	400 lines
Frequency range
Normal audio	: 70 Hz to 10,000 Hz
Hi-Fi audio	: 20 Hz to 20,000 Hz
Input/Output	: RCA connectors (IN x 2, OUT x 1)
		S-video connectors (IN x 2, OUT x 1)

TUNER

Tuning system	:	Frequency-synthesized tuner
Channel coverage
VHF	: Channels 2–13
UHF	: Channels 14–69
CATV	:	113 Channels
RF output	: Channel 3 or 4 (switchable; preset to
		Channel 3 when shipped) 75 ohms,
		unbalanced

TIMER

Clock reference	:	Quartz
Program capacity	:	1-year programmable timer/
		8 programs
Memory backup time	:	Approx. 3 min.

ACCESSORIES

Provided accessories	: Infrared remote control unit,
	“AA” battery x 2,
	Audio/video cable,
	RF cable (F-type),
	S-video cable (4-pin),
	Controller

Specifications shown are for SP mode unless specified otherwise. E. & O.E. Design and specifications subject to change without notice.

— 26 —