JVC LPT0991-001A manual Link Functions, Language for the on-screen display DVD deck, Just Clock

14 INITIAL SETTINGS (cont.)

Results of Auto Set Up/Preset Download Appear on the Front Display Panel

If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed.

Turn on the TV and select its video channel or AV mode, then make sure that all necessary stations have been stored in the unit’s memory by using the PR button(s).

●If station names (ID –  pg. 62) have also been stored in the unit’s memory, the station name will be displayed at the top left corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

●If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 60 – 62.

If Auto Channel Set has succeeded but Auto Clock Set has not, “1” (channel position) is displayed.

ATurn on the TV and select its video channel or AV mode, then make sure that all necessary stations have been stored in the unit’s memory by using the PR button(s).

●If station names (ID –  pg. 62) have also been stored in the unit’s memory, the station name will be displayed at the top left corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

●If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 60 – 62.

BPerform “Clock Set” on page 65.

If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.

Make sure the cables are connected properly and turn off the unit’s power once, then turn the unit’s power back on again. Perform “Auto Set Up” on page 12 or “Preset Download” on page 13 again.

IMPORTANT

●To check if the Guide Program numbers have been set

correctly, perform the VIDEO Plus+ Timer Programming. ( pg. 24) (VHS deck only)

●In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the VIDEO Plus+ system, the unit will record a TV programme of a different station. When programming the timer using the

VIDEO Plus+ system, be sure to check the desired channel is selected correctly. ( pg. 24, “VIDEO Plus+® Timer Programming”) (VHS deck only)

●Your unit memorizes all detected stations even if reception of

some of them is poor. You can delete those stations with an unacceptable picture. ( pg. 60, “Deleting a Channel”)

INFORMATION

Language for the on-screen display (DVD deck)

About the on-screen language for the DVD deck, see page 15.

Just Clock

Your unit is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON.” ( pg. 65, “Just Clock”)

If you have any difficulty with the above procedures call the JVC Customer Service Hot Line on 0870 330 5000

T-V Link Functions

When you connect the unit to your TV via a fully-wired 21-pin SCART cable ( pg. 11), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.*

For details, refer to the instruction manual of your TV.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link or DATA LOGIC via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you play a tape.

For details, refer to the instruction manual of your TV.

Unit Auto Standby

You can use your TV’s remote control to turn off the unit. For details, refer to the instruction manual of your TV.

Direct Rec (VHS deck only)

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON.” ( pg. 53)