Manuals / Brands / Photography / Security Camera / JVC / Photography / Security Camera

JVC LST0728-001B Memo :, Note :, 5 Press the [Disconnect] button to disconnect the camera

1 162

Download 162 pages, 19.53 Mb

4 Press the [Connect] button to connect to the camera and start audio transmission

●Connection status with the camera is displayed in the [Status] area of the [Status Information] list. Press the [Connect] button and audio sound that input to [AUDIO IN 1] terminal of this unit will be transmitted to the cameras that are displayed as A Connected B.

●If A Disconnected B appears, check the network between this unit and the camera, IP address of the camera, and the power of the camera. If [Authentication failed] appears, repeat procedures on the [Event Audio Setting] screen to register the password of the camera for which the [Authentication failed] message is displayed.

[Password] (A Page 130)

5 Press the [Disconnect] button to disconnect the camera

Memo :

●Cameras that are not registered in [Camera Record Setting] of the main menu cannot be selected.

●If the audio setting of the camera is set to the half duplex mode,

you will not be able to hear audio sound from the camera when in the A Connect B status.

●If you are sending the microphone sound to a camera for which an event audio has been set, the audio playback function that is associated with an event will be disabled during microphone sound transmission, and priority is given to the microphone sound transmission.

●You can also operate the [Connect] and [Disconnect] button from the alarm terminal on the rear panel. In this case, select the alarm terminal to be used for control with [Push To Talk] under [Event Audio Setting]. An alarm input triggers an action equivalent to the [Connect] button, and canceling the alarm is equivalent to the action when you pressed the [Disconnect] button. Control of the [Connect] and [Disconnect] is valid only when these buttons are enabled.

Note :

●If you are configuring the settings or performing an audio playback test in the [Camera Record Setting] or [Event Audio Setting] of the main menu, do so after you have closed this dialog box.

●If the performance meter lights up in yellow or red, the microphone sound may be interrupted. To make sure that audio sound is successfully transmitted, perform operations such as temporarily stopping the recording operation so that the performance meter does not light up in yellow or red. [Performance Meter] (A Page 27)

127

Contents

VR-N900U(B) Powered by Milestone Page SAFETY PRECAUTIONS (for USA) Please use this unit in an appropriate power source SAFETY PRECAUTIONS PRECAUTIONS WHEN MOUNTING RACK CAUTION INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA) WARNING (FOR EUROPE): SICHERHEITSVORKEHRUNGEN (for Germany) Page Page E/VR-N900U Getting Started Automatic detection of network cameras Display and distribution performance at 80 ips is guaranteed (VR-N1600U/E) Supports RAID1 (VR-N1600U/E) Built-in large-capacityhard disk (500 GB) (VR- N1600U/E) 1. Grant of Use 2. Copyright 3. No Warranties 4. Limitation of Liability 5. Miscellaneous Microsoft Software License Terms for: WindowsXP Embedded Runtime 2 Additional Licensing Requirements and/or Use Rights 3 Scope of License Page Microsoft Software License Terms for: (continued) 4 Windows Update Agent (also known as Software Update Services) Product Support Backup Copy Proof Of License 12 Liability Limitations 13 Export Restrictions Getting Started Preparation Basic Operation Applications Locations of Storage and Use Handling Precautions Precautions for Handling Hard Disk Drive Clock Precautions when Moving this Unit Precautions for Handling Power Cords Maintenance Energy Conservation Copyright CDE L[STOP(PB)] Button M[PLAY] Button N[SKIP] Button OJog dial PShuttle dial Rear Panel U[POWER] switch V[AC IN 120V H 240VH 50Hz/60Hz] power input terminal W[AUDIO IN 1/AUDIO IN 2] audio input terminals 1/2 (RCA) X[AUDIO OUT] audio output terminal (RCA) Rear I/O Terminals e f h j l n g i km o Input ports e[ALARM IN 1 to 8] alarm input terminals 1 to f[EMERGENCY] emergency input terminal Front Panel CDE F G H I J K L M N O A [OPERATE] Button/Indicator J[SEARCH] Button K[KEY] Button L[ALARM CLEAR] Button M[REC/STOP] Button N[STOP(PB)] Button W[POWER] switch X[AC IN 120V H 240VH 50Hz/60Hz] power input terminal Y[RESET] Z[AUDIO IN 1/AUDIO IN 2] audio input terminals 1/2 (RCA) a[AUDIO OUT] audio output terminal (RCA) j[ALARM IN 1 to 4] alarm input terminals 1 to k[EMERGENCY] emergency input terminal l[ALARM RESET] alarm reset input terminal m[EXT REC IN] external recording input terminal n[OPE ON/OFF] Operate ON/OFF terminal Page Camera Control Terminal (VR-N900U) When name of control button is different Press the [16/ENTER](ZOOM IN/ENTER)button. When operating method is different 1 Mount the rack mount bracket using screw (1) Setting Operation Lock Canceling Operation Lock Before Starting Up Starting the unit 1 Turn on the power switch at the rear panel Selecting a language 1 Select a language Automatic Registration of Cameras 2 Check to ensure that the camera is detected 3 Replace the detected camera accordingly in sequence Automatic Registration of Cameras (continued) 7 Enter the password for the network camera After password entry is complete, press [KEY] again the close the software keyboard Use the [SKIP] button to select [OK], followed by 12 Repeat Step 10 for each camera Preparation VR-N900U VR-N1600U/E Page Entering Characters Using a Mouse 1 Press the [KEY] button on the front panel 3 Click on the character 1 Press the [KEY] button 2 Move the mouse pointer with the keypad (arrow key) Page Basic Operation Switching the Power On 1 Connect the power cable 2 Turn AONB the power switch at the rear panel Switching the Power Off Enter the password using the keypad, and press the 1 Press and hold the [REC/STOP] button for at least 2 seconds 3 Select an item For details on the main menu settings, refer to [Main Menu List] (A Page 68) Page 1 Press the [SELECT] button 2 Enter the camera number with the keypad Operating the Camera Pan/Tilt 1 Press the [PTZ/PRESET] button to switch the keypad to the PTZ mode 2 Press the 1 to 9 key on the keypad Zoom In/Zoom Out 1 Select [Live] from the main menu Viewing Images Using the PTZ Features 1 Click the PTZ navigation button in the [PTZ Control] section Viewing Images Using the PTZ Features (continued) Digital Zoom Using Preset Positions 1 Click the [v] button on the [Presets] list in the [PTZ Control] section 2 Select a preset position from the preset list Manually Triggering an Event Triggering Outputs Camera Shortcut Menus select a view Displaying the [Browse] Screen 2 When the [Live] screen appears, press the [LIVE/BROWSE] button again Searching Recorded Image Using a Specific Date/Time 1 Press the [SEARCH] button on the [Browse] screen Control using the [PLAY], [SKIP], and [STOP(PB)] buttons on the front panel Playing Back 1 Press the [PLAY] button Skipping 1 Press the [SKIP] button Notes: 2 Double-clickthe [Browse] tab on the NVR Viewer Searching Recorded Image Using [Time Navigation] 1 Double-clickthe [Time Navigation] bar on the [Browse] screen 2 Select the search date/time from the box 3 Click the [Go To] button Searching Recorded Image Using the Timeline Browser Timeline Colors and Lines Searching Recorded Image Using Sequence 1 Double-clickthe [Sequence] bar on the [Browse] screen 2 Click [Get Sequence] Searching Recorded Image from the Alert List 1 Double-clickthe [Alerts] bar on the [Browse] screen 2 Click [] on the [Alerts] list and select an event from the list 3 Click the [Get List] button Smart Search Browse Button [Time] Slider [Playback] Slider Listening to Audio Sound Burning a CD/DVD 1Double-clickthe [Export] bar on the [Browse] screen 2Enter the start date and time 3Enter the end date and time Burning a CD/DVD (continued) 5 Select the export format if you have selected [AVI/JPEG Export...] 6 Select the required frame rate if you have selected the [AVI] format 10 Specify the export destination 11 Click [Export] 12 When export is complete, connect the CD/DVD drive to this unit 13 Press and hold the [FUNCTION] key in front, and press [4] on the keypad 16 Press the [Burn] button Deleting Temporary Files (Operation on the Unit) 1 Select the temporary files you want to delete from the data list 2 Click the [Erase Sel Data] button Deleting Data from a CD-RW(Operation on the Unit) 1 Insert the CD-RW 1Double-clickthe [Print] bar on the [PLAY] screen 2 Click the [Print...] button in the [Print] section 4 Click the [Print] button to start printing Recording Modes Recording Control Mode (A Page 53) Manual Recording Mode [EXT REC IN] Signal Recording Mode Emergency Recording Mode Selecting the Recording Control Mode Selecting the Manual Recording Mode 1 Press the [REC/STOP] button Scheduler Setting 1 Select [Camera Record Setting] from the main menu Scheduler Setting (continued) 4 Select [Set] from [Mode] 5 Select the [Online] check box 6 Specify the date to switch online in the calendar section 7 The Schedule Settings window appears Camera/Alert Scheduler Screen A B C Display Bar Specifying Image Recording Settings 2 Select a camera from [Device Manager] and click [Settings...] Settings Conditionally Settings (continued) Setting Picture Quality 2 Select a camera from [Device Manager] and click [Camera Settings] 3 Click [Image Quality...] Specifying Audio Recording Settings Precautions when enabling the analog audio source of VR-N1600U/E Renaming Cameras and Assigning Camera Numbers 1 Select a camera name and right-clickon it, followed by clicking [Edit] Screen Display (Groups and Views) Creating Groups and Views Creating a group 1 Select [Screen Setup] from the main menu Creating [Views] within a group 1 Select the group in which you want to create a new view 2 Click the [Rename] button Creating Groups and Views (continued) 3 Enter a name for the new view 3 Overwrite the existing group or view name with a new name Renaming a group/view Adding Cameras to a View 1 Select a view 2 Click the [+] mark to the left of [Server] under [System Overview] Adjusting Camera Settings 1 Select the camera you want to adjust on the [Screen Setup] screen Adjusting Camera Settings (continued) Using Your Views on Different Computers 1 Double-clickthe [Setup] tab on the NVR Viewer 2 Select the folder you want to use in the [Views] section Adding a Carousel 3 Release the mouse button at the position Adding Hot Spots (Enlarged Images) Using the [Html Page] 1 Click [Html Page] under [System Overview] 2 Drag and drop at the required position using the mouse Type in the URL and click [OK] Select [Html Page] under [Views], and specify Applications List of Menu Screens Unit Setting Unit Setting (continued) NONE Average File Size OS Setting Network Adapter OS Setting (continued) Page Image Server Setting Page Image Server Setting (continued) BUser Administration (continued) Page Auto Detect Setting Enable Auto Detect Setting (continued) Page Camera Record Setting Page 4 If an administrator password is specified for the device, enter the password 5 Enter a unique name for the device that has been detected 6 Click [Finish] Analog Cameras (VR-N900U) 2 Click [Add Device...] Page D E F G [CAMERA CONTROL] Terminal at the Rear of VR-N900U (VR-N900U) Stopping the Recording Server Display the [PTZ Preset Positions for Device Name] window 2 Click the [Service Manager...] button 3 Click the [Pause] button 3 Click the [PTZ Preset Positions...] button Move the camera and determine the position using the [PTZ View] Moving to Preset Positions by Events 1 Display the [PTZ Preset Positions for Device Name] window (A Page 90) Defining a Preset Position Auto PTZ Patrolling 2 Click the [Setup...] button of [Patrolling] A B C D Auto PTZ Patrolling (continued) Specifying Patrol Timing PTZ Patrolling Actions Upon Detection of Motion 1 Select the [Disable patrolling schedule if motion is detected] check box 2 Select the conditions for resuming PTZ patrolling I/O Settings 1 Click the [I/O Setup...] button on the [Camera Record Setting] screen I/O Settings (continued) Specifying an Input Event 2 Click the [Add new event...] button F E BD C Input/Output Terminal on Rear Panel Rear Panel Input Terminals Output Terminals Specifying a VMD Event 2 Click the [Add VMD Event(Motion Detection)] button Specifying an Output 2 Click the [Add new output event...] button [Advanced] Screen 1 Click the [Advanced...] button on the [I/O Setup] screen 2 Specify the following items Configuring Event Buttons 2 Select [Global] (apply to all cameras) or a specific camera 3 Click [Add new event...] to add the event button Specifying Generic Events 2 Select Generic and click [Add new event...] AC B AGeneral Event settings BNotification settings CEvent rules string 5 Repeat 2 to 4 for each event Specifying an Output Port Event Notification Settings 2 Click the [Event Notifications...] button 1 Select [I/O Control] from the [Camera Record Setting] screen Camera Output Settings Specifying Output via Motion Detection Select an output from the [All Output] list Click the button between the [All Output] Defining Motion Detection Exclusion Regions Setting Buttons and Check Boxes Specifying Motion Detection 2 Specify [Noise Sensitivity] and [Motion Sensitivity] Page Page E mail Settings 1Click [Camera Recording Administator]-[Archive Setup] K J G H 4 Select the camera for which archive is to be created Precautions when Changing NAS Archive Settings Precautions when Changing Archive Settings Specify the database settings 1 Select [Flash Memory Utility] from the main menu Save Setting Date 2 Select [Save Setting Date] 3 Press the [OK] button 4 Select [Remove Flash Memory] Reading Preset Data 2 Select [Load Setting Data] 3 Select the setting to load, followed by pressing [Load] 4 The [Load Setting Data?] confirmation message appears. Press [OK] 5 Press [Close] to return to the [Flash Memory Utility] screen Specifying IP Lease 1Select [Auto Detect Setting] from [Main Menu] 2 Select [Enable] in [IP Lease] 3 Specify the following items under [IP Lease Parameter] 4 Click [OK] Using the Auto Detect Feature 3 Configure the analog input (VR-N900U) 4 Click [Entry] 5 Click [OK] 1NR-N900U 1 Exit NVR Viewer 2 Select [Language Setting] from the main menu 3 Select a language 4 Click the [OK] button 1 Select [HDD Utility] from the main menu 1 Select [Return to default setting] from the main menu 2 Click [OK] User Administration User Settings Defining User Rights 1 Select [Restrict user access] in the [User Administration] section 2 Click [User Access...] 3 Select the user for which user right is to be specified from the [User] list 5 Select the camera to allow access from the [Defined Cameras] 6 Click [] to move to [Viewable by selected user] 8 Repeat the same procedures for other users 1 Click the [Start] button, followed by clicking [Control Panel] System requirements Computer Network Settings 2 Click [Network and Internet Connections] [Network Connections] 3 Select the network to which NVR is connected 4 Right-clickand select [Properties] 6 Select [Internet Protocol(TCP/IP)] and click the [Properties] button 7 Select [Use the following IP address] 8 Set [IP address] to Install the NVR Viewer on the computer 3 Click the [Run] button 4 Click [Next] and follow the installation instructions 2 Click [Download and install NVR Viewer locally] Login to the NVR Viewer 1 Double-clickthe NVR Viewer shortcut on the desktop 5 Installation complete Login to NVR Viewer (Continued) 2 Specify your login information in the following fields 3 Click the [Connect] button 4 Set the display language according to the country of use Uses of the NVR Viewer Exiting/Logging Out of the NVR Viewer Logging Out 1 Click the [Log Out] button Exiting Audio Transmission 1 Start up the NVR Viewer to check the live images of the camera Connection 1 Refer to [System Connection Example] Registering camera that supports bidirectional audio 5 Press the [Disconnect] button to disconnect the camera 1 Select [Event Audio Setting] from [Main Menu] A B Audio Copying 1Click [Audio files copy] on the [Event Audio Setting] screen Password Setting Copy 2Click [Setting copy] A Source event Communication Settings 1Click [Communication setting] on the [Event Audio Setting] screen A Event receive port Compatible Network Cameras Connecting a UPS 2 Select AUPS ModeB and press the [OK] button 3 Connect the UPS communication cable to the [SERIAL] port on the rear panel 4 Connect the power cable of this unit to the UPS power output connector 5 Check the entry in the [Volume] field, and click the [Initialize] button NAS Pressing a Button for Two Seconds or Longer [REC CONTROL] Combining a Button with the [FUNCTION] Button [FUNCTION] + [REC CONTROL] [FUNCTION] + [LIVE/BROWSE](VR-N1600U/E) 2 Select AOn motionB or AOn eventB Zoom Iris Focus Speed Preset Page Starting the Export Viewer 4 Double-clickthe data folder in the list on the right side of the Explorer 5 Double-click [Browser.exe] in the list on the right side of the Explorer Viewing Exported Data Viewing Data on a Specific Date/Time Using Date/Time Selection Exiting the Export Viewer 1 Go to the Start menu, and select [File]-[Close] Viewing Data on a Specific Date/Time Using Timeline 1 Drag the mouse pointer upwards or downwards on the Timeline Select a joystick from the selected joystick list 1 Click the [K] button at the top right corner of the screen 2 Select [Joystick Setup] from the menu that appears 5 Assign an action to each joystick button in the [Button Setup] section Disabling Joystick Operation 1 Click [HDD Utility] under [Main Menu] (A Page 116) 2 Click [Details] 6 Click [Close] 7 Click [Main Menu]-[CameraRecord Setting]- [Archive Setup...] (A Page 108) 8 Deselect the [Automatic path selection] check box Page Page 9 channel recording without audio recording or additional HDD upgrade 9 Channel Recording/No Audio Recording/No Additional HDD 9 Channel Recording/2 Channel Audio Recording/No Additional HDD 9 Channel Recording/No Audio Recording/Additional HDD (1 TB x 1 Unit) 9 Channel Recording/2 Channel Audio Recording/Additional HDD (1 TB x 1 Unit) Page Page Page Page Page Actions when Warning Indicator Lights Up VR-N1600U/E General Interface Compression Format Recording VR-N900U General