Others

Compatible Equipment

Make sure that peripheral devices are used in accordance with their operating environment.

Compatible Network Cameras

Function

JPG

PTZ

Audio

PTZ

MPG4

VMD

IP cameras

Joystick

Event

 

 

 

 

JVC

R

 

 

 

R

 

VN-V25U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

 

R

 

R

 

VN-V26U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

R

 

R

R

 

VNV686U

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

R

 

 

 

 

VN-C20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

R

 

R

 

 

VN-C655

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

R

 

R

 

 

VN-C625

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

R

R

R

 

 

VN-E4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JVC

R

R

 

 

 

 

VN-C215

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AXIS 206

R

R

 

 

 

 

AXIS 207

R

R

 

 

R

R

 

 

 

 

 

 

 

AXIS 211

R

R

R

 

R

R

 

 

 

 

 

 

 

AXIS 212

R

R

R

R

R

R

AXIS 213

R

R

R

R

R

R

 

 

 

 

 

 

 

AXIS 214

R

R

R

R

R

R

 

 

 

 

 

 

 

AXIS 216

R

R

R

 

R

R

AXIS 225

R

R

 

 

R

R

 

 

 

 

 

 

 

Verint S1700

 

R

 

R

R

 

 

 

 

 

 

 

 

Verint S1704

 

R

 

R

R

 

Verint S1708

 

R

 

R

R

 

 

 

 

 

 

 

 

Verint S1900

 

 

 

 

R

 

 

 

 

 

 

 

 

Verint S2700E

 

 

 

 

R

 

Memo :

●When sending out audio data to VN-V26U, make sure that the firmware version of VN-V26U is 1.01 or a newer version. (VR- N1600U/E)

Connecting a UPS

Connecting an uninterruptible power supply (UPS) to the hard disk will protect it from damage by automatically shutting down all operations prior to switching off the power supply in the event of a power failure.

1 Press and hold the [FUNCTION] button, and press the [3/] keypad button at the same time to start up the [UPS SetUp] screen

2 Select AUPS ModeB and press the [OK] button3 Connect the UPS communication cable to the [SERIAL] port on the rear panel4 Connect the power cable of this unit to the UPS power output connector
5 Switch on the power of the UPS, followed by the power of this unit

Note :

●Consult your nearest JVC dealer or service center for details on the types of UPS that can be used.

●Make sure that the UPS communication cable is connected before switching on the power of this unit.

●Do not disconnect the communication cable when operations are in progress.

●When a power failure occurs while formatting a hard disk or archiving, subsequent operations may be affected even when a UPS is connected.

●The recorded images may not be played back properly if they are not archived before the power failure. (A Page 110)

●If you are not using a UPS, do not select [UPS SetUp] on the the [UPS SetUp] screen. Inappropriate selections may affect subsequent operations.

External Hard Disk Drives

You can connect an external hard disk drive to the serial terminal at the rear of this unit. External hard disk drives can be combined with this unit in the following ways. Combinations other than those below are not possible.

●500 GB (1 unit)

●1 TB (1 unit)

●1 TB (1 unit) + 2 TB (1 unit)

●2 TB (1 unit)

●2 TB (up to 2 units)

Connecting the External Hard Disk Drive

1 Press and hold the [OPERATE] button for about2 seconds to turn off the power

2 Turn off the power switch on the rear panel

Note :

●Make sure that you turn off the power switch.

3 Connect the external hard disk drive to the [SERIAL] port on the rear panel, and switch on the power

●Make sure that you switch on the power to the external hard disk drive before switching on this unit. The system may not recognize the external drive if it is not switched on beforehand.

4 Switch on the power of this unit

●If recording is in progress, a [New HDD was found. Are you OK to stop recording and format new HDD?] confirmation message appears.

132