22 English
■■
Specifications
Amplifier
Output Power
6 W per channel, min. RMS, at 4
Ω
from 150 Hz to 15
kHz with no more than 10% total harmonic distortion.
20 W per channel woofer, min. RMS into 4
Ω
at 60 Hz
with no more than 10% total harmonic distortion.
Input Sensitivity/Impedance (1 kHz)
AUX IN 300 mV/47 k
Ω
MIC/GUITAR INPUT: Switchable
MIC 200
Ω
– 2 k
Ω
(6.3 mm dia. plug)
GUITAR 100 k
Ω
– 1 M
Ω
(6.3 mm dia. plug)
Output Sensitivity/Impedance (1 kHz)
Phones 16
Ω
– 1 k
Ω
0 – 12 mW/ch output into 32
Ω
Cassette Deck
Frequency Response
Type II (High position) 60 Hz – 14 kHz
Wow and Flutter 0.15% (WRMS)
Disc Player
Dynamic range 90 dB
Signal-to-noise ratio 95 dB
Wow and Flutter Unmeasurable
Tuner
WIRELESS
Tuning Range 87.50 MHz – 108.00 MHz
FM Tuner
Tuning Range 87.5 MHz – 108.0 MHz
AM Tuner
Tuning Range 530 kHz – 1 710 kHz
Antenna FM telescopic antenna
Ferrite core antenna for AM
Speakers
Full range 8 cm
×
2, 4
Ω
Super woofer 16 cm
×
2, 4
Ω
Wireless Transmitter (VFT-001) Power RequirementsDC 3 V (“R6/AA(15F)” batteries [2])
Transmitting Frequencies
88.10 MHz, 88.30 MHz, 88.50 MHz,
88.70 MHz, 107.10 MHz, 107.30 MHz,
107.50 MHz, 107.70 MHz
Input terminal Stereo mini plug
Frequency response 50 Hz to 12 000 Hz
Battery life (at normal temperature)
Approx. 50 hours (with Alkaline batteries)
Approx. 20 hours (with Manganese batteries)
Dimensions 78 mm
×
55 mm
×
35 mm (W/H/D)
Mass Approx. 50 g (without batteries)
General
Dimensions 690 mm
×
239 mm
×
296 mm (W/H/D)
Mass 9.5 kg (without batteries)
10.6 kg (with batteries)
Power Specifications
Power RequirementsAC 120 V , 60 Hz
DC 15 V (“R20/D(13F)” batteries [10])
External DC 12 V (car battery via optional
CA-R120 car adapter)
Power Consumption 50 W (power on mode)
1.6 W (in standby mode)
Symptom Possible cause Action
Unable to operate the remote control. • The path between the remote control and
the sensor on the system is blocked.
• The batteries have lost their charge.
• Remove the obstruction.
• Replace the batteries.
Operations are disabled. The built-in microprocessor has
malfunctioned due to external electrical
interference.
Unplug the system then plug it back in
after a few minutes.
The cassette holder cannot be opened. During tape play, the power cord has been
unplugged.
Plug in the power cord and press the
ON/STANDBY button.
Indicators and the display do not light up
while in standby mode.
Batteries or DC power is used to supply
the power.
Design and specifications are subject to change without notice.
EN07-22_RV-NB10[C]f.fm Page22 Tuesday, January 24, 2006 2:07 PM