English
3.Adjust the effect level.
1)Press (BALANCE/) SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display. The display changes to show the current setting.
2)Turn MULTI JOG to select the effect level.
•As you turn it, the effect level changes as follows:
BALANCE/SURROUND
ADJUST
MULTI JOG
Adjusting the Surround Modes
Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.
Dolby/DTS/MPEG Surround adjustments
Before you start, remember...
• Make sure that you have set the speaker information correctly |
(see page 14). |
• There is a time limit in doing the following steps. If the setting is |
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 5DSP EFFECT 4
As the number increases, the selected DAP mode becomes stronger.
From the remote control:
1. Press SURROUND MODE | SURROUND |
| |
repeatedly until the DAP mode — | MODE |
| |
LIVE CLUB, DANCE CLUB, |
|
HALL, or PAVILION — appears |
|
on the display. |
|
The DSP indicator also lights up on the display.
•When you have set “REAR SPK” to “NONE,” the 3D- PHONIC indicator also lights up.
2. Press SOUND. | SOUND |
|
The 10 keys are activated for sound adjustments.
3. Adjust the speaker output levels. |
|
| REAR•L | |
• To adjust the left rear speaker level, press | 5 | 6 | ||
REAR•L | ||||
|
| ENTER |
•To adjust the right rear speaker level, press REAR•R
REAR•R
canceled before you finish, start from step 1 again. |
• You cannot adjust the rear speaker output levels when you have set |
“REAR SPK” to “NONE.” See page 14. |
• You cannot adjust the center speaker output level when you have |
set “CENTER SPK” to “NONE.” See page 14. |
From the remote control:
1. Press SURROUND ON/OFF to | SURROUND |
activate an appropriate surround | ON/OFF |
| |
mode — PRO LOGIC, DOLBY |
|
DIGITAL, DTS SURROUND, or |
|
MPEG SURROUND. |
|
•Each time you press the button, the Surround mode turns on and off alternately
•When “PRO LOGIC” is selected, the ÙPRO LOGIC indicator lights up on the display.
Note:
You can also press SURROUND MODE to activate an appropriate
Surround mode.
2. Press SOUND. | SOUND |
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker
output balance. | TEST | |
4 | ||
“TEST TONE L” starts flashing on the |
4.Press EFFECT to select an effect level you want.
•Each time you press the button, the effect level changes as follows:
8 9
EFFECT
7/P
display, and a test tone comes out of the |
|
|
|
| ||||||
speakers in the following order: |
|
|
|
|
| |||||
| TEST TONE L |
| TEST TONE C |
| TEST TONE R |
| ||||
| (Left front speaker) |
| (Center speaker) |
| (Right front speaker) | |||||
|
| TEST TONE LS | TEST TONE RS | |||||||
|
| (Left rear speaker) |
| (Right rear speaker) |
|
|
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 5 | DSP EFFECT 4 |
As the number increases, the selected DAP mode becomes stronger.
Notes:
•You can adjust the speaker output levels without outputting the test tone.
•No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 14).
•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 14).
•If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.
29