Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
| ||||
|
|
|
|
|
|
|
| |
| The display does not light up. | The power cord is not plugged in. | Plug the power cord into an AC outlet. |
| ||||
|
|
|
|
|
|
|
| |
| No sound from speakers. | Speaker signal cables are not connected. | Check speaker wiring and reconnect if |
| ||||
|
|
| necessary. |
|
|
| ||
|
|
|
|
|
|
|
| |
|
| The SPEAKERS 1 and 2 buttons are not | Press SPEAKERS 1 and 2 correctly. |
| ||||
|
| set correctly. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| An incorrect source is selected. | Select the correct source. |
|
|
| ||
|
|
|
|
|
|
|
| |
|
| Muting is activated. | Press MUTING to cancel the mute. |
| ||||
|
|
|
|
|
|
|
| |
| Sound from one speaker only. | Speaker signal cables are not connected | Check speaker wiring and reconnect if |
| ||||
|
| properly. | necessary. |
|
|
| ||
|
|
|
|
|
|
|
| |
|
| The balance is set to one extreme. | Adjust the balance properly (see page 13). |
| ||||
|
|
|
|
|
|
|
| |
| Continuous hiss or buzzing during FM | Incoming signal is too weak. | Connect an outdoor FM antenna or contact |
| ||||
| reception. |
| your dealer. |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| The station is too far away. | Select a new station. |
|
|
| ||
|
|
|
|
|
|
|
| |
|
| An incorrect antenna is used. | Check with your dealer to be sure you have |
| ||||
|
|
| the correct antenna. |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| Antennas are not connected properly. | Check connections. |
|
|
| ||
|
|
|
|
|
|
|
| |
| Occasional cracking noise during FM | Ignition noise from automobiles. | Move the antenna farther from automobile |
| ||||
| reception. |
| traffic. |
|
|
| ||
|
|
|
|
|
|
|
| |
| No colors on the | The color system of the connected TV is | Connect PAL- or |
| ||||
|
| not PAL. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Howling during record playing. | Your turntable is too close to speakers. | Move speakers away from the turntable. |
| ||||
|
|
|
|
|
|
|
|
|
| “OVERLOAD” starts flashing on the | Speakers are overloaded because of high | 1. Press STANDBY/ON |
| on the front |
| ||
|
|
| ||||||
|
|
| ||||||
| display. | volume. | panel to turn off the receiver. |
| ||||
|
|
| 2. Stop the playback source. |
| ||||
|
|
| 3. Turn on the receiver again, and adjust the |
| ||||
|
|
| volume. |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| Speakers are overloaded because of short |
|
| on the front panel, |
| ||
|
| Press STANDBY/ON |
|
|
|
| ||
|
|
|
|
| ||||
|
| circuit of speaker terminals. | then check the speaker wiring. |
| ||||
|
|
| If “OVERLOAD” does not disappear, unplug |
| ||||
|
|
| the AC power cord, then plug it back again. |
| ||||
|
|
| If speaker wiring is not |
| ||||
|
|
| your dealer. |
|
|
| ||
|
|
|
|
|
|
|
| |
| Remote control does not work. | The remote control mode selector is not | Set the selector correctly either to “AUDIO/ |
| ||||
|
| set correctly. | TV/VCR” or to “CATV/DBS.” |
| ||||
|
|
|
|
|
|
|
|
|
|
| There is an obstruction in front of the | Remove the obstruction. |
|
|
| ||
|
| remote sensor on the receiver. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Batteries are weak. | Replace batteries. |
|
|
| ||
|
|
|
|
|
|
|
|
|
English
54